Military Engineer Services-MES has published Special Repairs To Bore Well At Pump House No 9 In Pj Enclave And 18 Nos Of Chemical Earthing Infrastructure For Command Building P-28 At North Camp At Afs Bamrauli. Submission Date for this Tender is 11-03-2021. Electrification Work Tenders in Bamrauli Uttar Pradesh. Bidders can get complete Tender details and download the document.
Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
1 | 04-Mar-2021 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 11-03-2021 |
Name of Work: SPECIAL REPAIRS TO BORE WELL AT PUMP HOUSE NO 9 IN PJ ENCLAVE AND 18 NOS OF CHEMICAL EARTHING INFRASTRUCTURE FOR COMMAND BUILDING P-28 AND PROVISION OF POST TOP LATERN AT SHOPPING COMPLEX AT NORTH CAMP AT AFS BAMRAULI | |||||
---|---|---|---|---|---|
Sl. No. | Item Description | Item Code / Make | Quantity | Units | |
1 | 1 | Lifting of submersible pump 30 HP along with column pipes 10 Nos and submersible cable 16 Sqmm from the old bore well at Pump house No. 9 including lowering of the same submersible pump to new bore complete all as specified and directed. | 1 | Job | |
2 | 2 | Trial bore well of 250mm dia size pilot bore through any soil strata including hard stone/boulder by means of direct rotary method below ground level complete all as specified & directed by Engineer-in-Charge. | 210 | RM | |
3 | 3 | Drilling reaming vertical bore 610 mm dia at approved site/location in any type of strata for 300 ERW casing pipe for various depth as shown below including all works pertaining to boring complete in all respects, as specified & directed. Note:- Reaming up to 610mm dia for 70 mtr depth from ground level for casing pipe 300mm dia" | 70 | RM | |
4 | 4 | All as per Sl Item No. 3 above but for Reaming up to 610mm dia for exceeding 70 mtr but not exceeding 200 mtr for casing pipe of 200 mm dia. | 140 | RM | |
5 | 5 | All as per Sl Item No. 3 above but for Reaming up to 610mm dia for exceeding 200mtr and not exceeding 250mtr. | 10 | RM | |
6 | 6 | Supply and assembly including jointing, lowering and fixing in position ERW plain steel pipe (Seamless) housing pipe 300mm bore (nominal dia) 8.00mm thick and outer dia of pipe 322mm conforming to IS-8110-2000 class 8.1.1 plain end pipe jointed and welded coupler ring (Welding shall be done throughout the circumference of the pipe and coupler ring both sides all as specified and directed by Engineer-in-Charge. Make : Jindal/Tata/Zenith . Note : (a) Length of pipe shall not less than 2.40 mtr except where the pipe length required is less than 2.40m (b) Effective length shall only be measured and paid. | 70 | RM | |
7 | 7 | All as per item No. 6 above but supply assembling, jointing ERW plain steel pipe (seamless) casing 200mm bore 8mm thick and outer dia of pipe conforming to IS 8110-2000 complete and lowering and fixing position after socket reducer of 300x200mm bore complete all as specified & directed by Engineer-in-Charge. | 90 | RM | |
8 | 8 | S&F MS strainer (slotted) pipe 'V' wired 200mm bore, 8 mm thick conforming to IS 8110-2000 fabricated with pipe slot of size 1.55mmx75mm as per IS provision uniformly distributed on the surface complete all as specified & directed by Engineer-in-Charge. | 30 | RM | |
9 | 9 | S&F mild steel reducing socket 300mmx200mm dia of suitable length including welding, mild steel strip 40x6mm 2 Nos on each joint extended in 75mm on each side complete all as specified and directed. Note :-The wall thickness of socket shall not be less than 7 mm thick. | 1 | Each Job | |
10 | 10 | S&F wrought iron bail plug 200mm bore complete all as specified and directed. | 1 | Each Job | |
11 | 11 | S&F well cap for 320mm dia housing pipe complete all as specified and directed. | 1 | Each Job | |
12 | 12 | S&F centring guide made out of 50x6mm MS flat iron on liner assembly complete all as specified and directed. | 60 | Each Job | |
13 | 13 | S&F 2 [TWO] Nos MS flat iron 150mm x 15mm housing clamp for holding to 300mm dia housing pipe with 16mm MS bolt & washers including casting of PCC blocks 1:2:4 type B-1 [Using 20mm graded stone aggregate] of size 1.20m x 1.00M including 50mm dia MS pipe 2 Nos each 1.5mtr long with cap plug and cap top for filling pea gravel including necessary excavation & each work in any type of soil complete all as specified and directed. | 1 | Each Job | |
14 | 14 | M&L for packing pea gravel of size 3 to 5mm natural shape brought direct from river bank and packing around casing pipe to entire depth up to ground level complete all as specified and directed. Note:- Length of assembly packed only will be measured for payment. | 50 | Cum | |
15 | 15 | M&L for development of tube well by means of over pumping high velocity fitting with 600 PSI air compressor all as specified in IS-8110-2000 para 4.3 including arrangement for equipment fitting and supply of sodium hepta sulphate 60 kg complete all as specified and directed. | 42 | Per Hour | |
16 | 16 | All as per Sl item No 15 above but by means of over pumping for subsequent hours until clear discharge as per clause 9.3 of IS 2800 (Part-1) -2009 complete all as specified and directed. | 45 | Per Hour | |
17 | 17 | Supply only strata sample box with glass cover 3mm thick and having internal dimension 1.0 mtr x 0.60 mtr x 0.10 mtr made out of shisham plank 20mm thick with hinges, hasp and staples including polishing complete with samples at various depth met at the time of boring including strata chart in duplicate complete all as specified and directed. | 1 | Each Job | |
18 | 18 | Chemical, biological and potability testing of water sample taken from the bore at Govt approved laboratory complete all as specified and directed.Note:- Test certificate obtained from approved lab will be submitted by the contractor in original. | 1 | Each Job | |
19 | 19 | Yield testing for bore well by continuous pumping for 16 hrs to determine safe pumping yield of the tube well complete all as specified and directed. | 1 | Each Job | |
20 | 20 | Electric logging in trial bore precise delineation of granular zones and also the quality of ground water including report interpretation complete all as specified and directed. Note: (a) Electric logging shall be carried out by approved agency. (b) Unit rate quoted by tenderer shall be deemed to be inclusive of cost of MS pipe and transportation of ring accessories as required, developing and testing etc at site of work and removal of the same on completion from the site including necessary supervision and rental charges of rig machine compressor & OP unit (any other T&P not specifically mentioned) and no extra payment shall be admissible on this account. | 1 | Each Job | |
21 | 21 | S&F discharge head body cast iron with air release valve suitable to connect column pipe of rising main flanged and column pipe or submersible pump set complete with nut, bolt washer etc including grouting 4 bolt on PCC platform complete all as specified and directed. Note :PCC platform will be measured and paid separately. | 1 | Each Job | |
22 | 22 | Supply, lowering, jointing and testing MS black column pipe 3 mtr long heavy duty 150mm bore wall thickness 5.4mm both ends flanged with heavy duty MS flanged not less than 16mm screwed and welded in side and outside. The flanged end making surface shall be smooth including welding of 04 strip of 5.04mm thick 25mm wide and 50mm long covering pipe and flanged, both end flanged having 08 Nos predrilled hole not less than 16mm including rubber gasket, nut bolts and washers, pipe should be duly painted with anti-corrosive paint complete all as specified and directed. | 13 | Each | |
23 | 23 | S&F PVC insulated flat copper submersible cable heavy duty 25 Sqmm 3 core 1100 volt grade complete all as specified and directed. | 330 | RM | |
24 | 24 | M&L for PVC pipe heavy grade 75mm bore and laid in trenches for protection of submersible cable with all fixing accessories etc complete all as specified. | 110 | RM | |
25 | 25 | Supply, fixing, jointing and testing of cast iron non return valve 150mm dia flanged ends as per IS-5312 (ISI Marked) complete with washers, nuts/ bolts and rubber gasket complete all as specified and directed. Make : Kiloskar/Upadhyay/Leader/Zoloto/L&T | 1 | Each | |
26 | 26 | Supply, fixing, jointing and testing of cast iron sluice valve 150mm class I (ISI marked) PN-1 type latest IS 14846-2000 flanged ends, drilled having stainless steel spindle with cast iron wheel head at top complete with nuts, bolts, washer and rubber gasket etc complete all as specified and directed. Make : Kiloskar/Upadhyay/Leader/Zoloto/L&T | 2 | Each | |
27 | 27 | Supply & laying in trenches ductile iron (DI) pipe of size 150mm bore dia with spigot and socketed ends centrifugally cast class 'K-7' in any length and jointing materials complete all as specified and directed. Make :Jindal/Tata/Electristeel/Lanco | 100 | RM | |
28 | 28 | M&L for 150mm bore Ductile iron (DI) fittings such as bends (any type, radius and angle) tapers any type,(straight, bend, increasing, decreasing or double socket etc) tee pieces single branch, “Y” junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs complete all as specified and directed. | 80 | Kg | |
29 | 29 | Supply, install, testing and commissioning of Busbar Chamber of size not less than 60cm x 60cm x 25cm for 3 phase, 415 volts AC, outdoor type, cubical compartmentalised type, weather, vermin and water proof, fabricated out of 2 mm thick CRCA sheet powder coated, front door openable with locking arrangement suitable for and including 100 amps rated copper bus bars suitable for connection 06 Nos terminal ends with adequate spacing of busbar insulated copper wire, with angle iron 40x40x6 mm frame bottom of the panel board, grouted by using PCC foundation 1:2:4 type B1 [Using 20 mm graded stone aggregate] thimbling and cable entry boxes with cable gland including painting with two coats of powder coated painted over a coat of red oxide primer complete all as specified and directed. | 1 | Each | |
30 | 30 | M&L for earthing complete with galvanized steel earth plate 600x600x6mm thick buried directly in ground (earth) pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connected to galvanised iron strip 32x6mm as earthing lead by means of bolts, nuts, check-nuts and washers of galvanised iron or steel besides welding at all joints as shown in drawings and including excavation and earth work, GI pipe light grade 40mm bore for protection of GI strip from earth electrode to and including the earth test point of galvanised Iron/steel of size 75mm x 75mm x 25mm, supplying and laying charcoal stone aggregate) chamber and mild steel angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B-1 using 20mm graded crushed stone aggregate reinforced with 8mm dia TMT BARS @ 75mm O/O both ways with mild steel handle 12mm dia, PGI funnel with wire mesh, 20 MM dia GI pipe light grade for watering all as shown in electrical plate No.3 of MES SSR Part - 1 | 3 | Each Job | |
31 | 31 | Excavation in trenches exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in soft/loose soil for foundations complete all as specified and directed. | 58 | Cum | |
32 | 32 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed. | 46 | Cum | |
33 | 33 | Removal of excavated material (soil) not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed. | 12 | Cum | |
34 | 34 | M&L for 100 mm thick plain cement concrete 1:2:4 type B-2 (Using 40mm graded stone aggregate) as in floor and finished concrete surface even and smooth without using extra cement complete all as specified and directed. | 20.25 | Sqm | |
35 | 35 | M&L for 100 mm thick plain cement concrete 1:4:8 type D-2 (Using 40mm graded stone aggregate) as in sub base of floors complete all as specified and directed. | 20.45 | Sqm | |
36 | 36 | M&L for reinforced cement concrete (RCC) M-25 Design Mix as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc basement slabs, under-reamed piles and mass concrete etc complete all as specified and directed. | 1.35 | Cum | |
37 | 37 | M&L for reinforced cement concrete RCC, M-25 Design Mix as in columns, pillars, posts and struts etc complete all as specified and directed. | 2.8 | Cum | |
38 | 38 | Use & waste of form to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar works vertical or to batter for fair finished surfaces foundation complete all as specified and directed. | 3.6 | Sqm | |
39 | 39 | Use & waste of form work to sides of columns, pillars, posts, struts, piers and stanchions for fair finished surfaces complete all as specified and directed. | 23.24 | Sqm | |
40 | 40 | M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. | 330 | Kg | |
41 | 41 | M & L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. | 99 | Kg | |
42 | 42 | M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of cement base primer complete all as specified and directed. | 18 | Sqm | |
43 | 43 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed. | 92 | Kg | |
44 | 44 | Taking out unserviceable earthing and supply, install, testing and commissioning of maintenance free chemical earth pit (Tripod Chemical Earthing) made of “Grid” chemical earth enhancing, non-ferrous compound containing no carbon or graphite which include (i) Three Nos 3000mm long 50mm dia copper bonded “Earth Electrode” prefilled with compound and stainless steel fasters, HDPE lockable earthpit cover cum inspection chamber along with 150 Kgs of Earth Enhancement, high conductive, corrosion resistant, non ferrous compound containing no carbon or graphite including bore hole of 150-200 mm and depth upto 3.3 mtr (approx). (ii) Copper earthing strip 25x3mm for interconnection of all three pits alongwith necessary clamps and nuts bolts. (iii) Any other accessories including design modification to achieve the required earth termination rod resistance valve below 1 ohms or as per the OEM/International Standard recommendation (iv) Mark earth result and date with paint (v) Ohms or as per the OEM / International Standard recommendation. Make: Tercel/Erico/Aes Gel earthing Solutions/ Indelec as approved by GE. | 18 | Each Job | |
45 | 45 | S&F 20x 3 mm copper strip on surface or in recess for connections etc including both end termination, suitable size strip clamps etc. from Equipment to the Earth pit terminal / Earth test link including taking out old unserviceable copper strip complete all as specified and directed. | 220 | RM | |
46 | 46 | S&F down conductor ISI marked 70 Sqmm PVC insulated copper flexible conductor including both end termination, suitable size cable clamps cooper thimbles etc. from equipment to the earth pit terminal / Earth test link including taking out old unserviceable copper conductor complete all as specified and directed. | 200 | RM | |
47 | 47 | S&F test point terminal block made of gun metal or phosphorus bronze size 75x75x25 mm drilled and screwed including 3 Nos 8mm dia 25 mm long hexa head screws including taking out old unserviceable test point terminal complete all as specified and directed. | 18 | Each | |
48 | 48 | S&F in replacement of 15 Watts LED post top lantern new generation, post-top energy saving environmental, long life aesthetically designed with symmetrical light distribution spun aluminium landscape with high power LEDs as light source complete all as specified and as directed. \nMake : Havells Post top lantern fitting Model No. CORALMINIPT15WLED757PSYMTOPC (or) techno commercially equivalent model in Philips/Wipro/Crompton/Bajaj as approved by GE\n | 20 | Each | |
49 | 49 | S&F in replacement of LED bulb 2 pin type 7 W complete all as specified and directed. Make : Philips/Havells/Wipro/Crompton/Bajaj\n\n | 20 | Each | |
50 | 50 | S&F Junction box for sign board light control made of PVC/SMC/FRP box of size 300x250x150 mm and connected MCB SP 06 Amps including necessary clamps, nuts, bolts etc as required complete all as specified and directed. \nMake :Sintex/Hansel/GE Power\n | 20 | Each | |
51 | 51 | Note :- Credit shown in credit schedule of tender document shall be considered by the tenderer while quoting the rates of various items. The same shall be recovered from various payment to contractor before handing over old material. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail