Indian Oil Corporation Limited-IOCL has published Wbso Engg . Modernization Of A Site Ro M/S Tara Maa Service Station With Extension Of Sales Building , Paver Block Driveway And Other Allied Civil , Mechanical And Electrical Work At Location Nandakumar Distt . Purba Medinipur Under Haldia Do. Submission Date for this Tender is 27-01-2021. Electromechanical Work Tenders in Vill-Irkha PO-Borakamardani Dist-Purba Medinipur West Bengal. Bidders can get complete Tender details and download the document.
Name of Work:Modernization of ‘A’ site RO M/s TARA MAA SERVICE STATION with Extension of Sales Building, Paver block driveway and other allied Civil, Mechanical & Electrical work at location Nandakumar Distt. Purba Medinipur under Haldia DO (West Bengal State Office) | |||||
---|---|---|---|---|---|
Sl. No. | Item Description | Item Code / Make | Qty | Units | |
1 | 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including taking out and disposal of excavated earth within or outside site to unobjectionable place and lift upto 1.5m, as directed by Engineer-in-charge. Disposed earth to be levelled and neatly dressed. Extra for levelling & neatly dressing of disposed soil completely to be paid separately as per item no. MPLCN00600 | ITEM CODE 1 | ||
2 | 2 | i) All kinds of Soil | ITEM CODE 2 | 99 | M3 |
3 | 3 | Extra for levelling & neatly dressing of disposed soil completely as directed by engineer in charge | ITEM CODE 3 | 20 | M3 |
4 | 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, within premises and lift upto 1.5m | ITEM CODE 4 | 50 | M3 |
5 | 5 | Supply & filling of local earth (including royalty) by mechanical transport also including ramming & watering of the earth in layers not exceeding 20cm in depth in plot, trenches, plinth, sides of foundations etc. complete | ITEM CODE 5 | 215 | M3 |
6 | 6 | Supplying and filling in plinth with sand within specified grading zone of fine aggregates specified in table 3.1, clause 3.1.3 of attached specifications under floors, etc. in layers not exceeding 20cm in depth, each deposited layer to be compacted by ramming including watering, consolidating and dressing complete. | ITEM CODE 6 | ||
7 | 7 | i) Local Fine Sand within grading zone IV | ITEM CODE 7 | 10 | M3 |
8 | 8 | Providing and laying in position cement concrete of specified grade excluding cost of centering & shuttering. All work up to plinth level: | ITEM CODE 8 | ||
9 | 9 | v) 1:3:6(1 Cement : 3 Coarse Sand : 6 Graded stone aggregate of 20mm) | ITEM CODE 9 | 5 | M3 |
10 | 10 | Centering and shuttering including strutting, propping etc. and removal of form work for: | ITEM CODE 10 | ||
11 | 11 | i) Foundations,footings,bases of column | ITEM CODE 11 | 46.05 | M2 |
12 | 12 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level | ITEM CODE 12 | ||
13 | 13 | ii) RCC 1 Cement :1½ Coarse Sand: 3 Graded Stone Aggregate 20mm | ITEM CODE 13 | 40 | M3 |
14 | 14 | Providing & Laying Reinforced cement concrete work in walls (Any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level UP TO FLOOR V LEVEL excluding cost of centering, shuttering, finishing and reinforcement : | ITEM CODE 14 | ||
15 | 15 | ii) RCC 1 Cement :1½ Coarse Sand: 3 Graded Stone Aggregate 20mm | ITEM CODE 15 | 31 | M3 |
16 | 16 | Centering and shuttering including strutting, propping etc. and removal of form for : | ITEM CODE 16 | ||
17 | 17 | i) Foundations,footings,bases of columns, etc. for mass concrete | ITEM CODE 17 | 100 | M2 |
18 | 18 | v) Columns, Pillars, Piers, Abutments, Posts and Struts. | ITEM CODE 18 | 81.11 | M2 |
19 | 19 | viii) Suspended floors, roofs,landings balconies and access platform with water proof ply 12mm thick | ITEM CODE 19 | 182.5 | M2 |
20 | 20 | ix) Lintels, beams, plinth beams, girders, bressumers cantilevers and with water proof ply 12mm thick | ITEM CODE 20 | 89.22 | M2 |
21 | 21 | Supply of Steel reinforcement for R.C.C. including straightening, cutting, bending, placing in position and binding all complete at all levels | ITEM CODE 21 | ||
22 | 22 | ii) Thermo Mechanically Treated Bars of Fe- 500D grade or more, conforming to IS1786 | ITEM CODE 22 | 6500 | KG |
23 | 23 | Providing and laying Brick work with common burnt clay F.P.S (non Modular) bricks of class designation 7.5 in foundation & plinth | ITEM CODE 23 | ||
24 | 24 | i) Brick work in Cement mortar 1:4 (1 cement : 4 coarse sand) IN FOUNDATION AND PLINTH | ITEM CODE 24 | 25 | M3 |
25 | 25 | iii) Brick work in Cement mortar 1:4 (1 cement: 4 coarse sand) in superstructure in all shapes & sizes in superstructure ABOVE PLINTH & UP TO FLOOR V LEVEL | ITEM CODE 25 | 25 | M3 |
26 | 26 | viii) Half brick masonry with common burnt clay F.P.S.(non modular) brick of class designation 7.5 in Cement mortar 1:4 (1 cement : 4 coarse sand) IN FOUNDATION AND PLINTH | ITEM CODE 26 | 60 | M2 |
27 | 27 | Providing & fixing chromium plated brass handles with necessary screws etc. complete: | ITEM CODE 27 | ||
28 | 28 | i) 125 mm | ITEM CODE 28 | 10 | EA |
29 | 29 | Providing & fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete : | ITEM CODE 29 | ||
30 | 30 | ii) 200x10 mm | ITEM CODE 30 | 8 | EA |
31 | 31 | Providing & fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete : | ITEM CODE 31 | ||
32 | 32 | i) 125 mm | ITEM CODE 32 | 12 | EA |
33 | 33 | Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogeneous fine cellular structure having smooth outer integral skin having 62mm width and 32mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38mm x 4mm & PVC solvent cement, including fixing the frame to wall with suitable dia and length anchor fastener as per manufacturer's specification and direction of Engineer-in-charge. | ITEM CODE 33 | 22.2 | M |
34 | 34 | Providing and fixing factory made 30mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75mm x 30mm having wall thickness 5mm. The styles, top & bottom rails shall have one side wall thickness of 15mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with MS tubes of size 33mm x 17mm x 1mm painted with primer, all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and rails with a cavity to receive single piece extruded 5mm PVC sheet as panel. The styles and rails shall be mitred cut and joint with help of PVC solvent cement and self tapping screws. Single piece extruded solid PVC lock rail of size 100mm x 30mm with wall thickness 5mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8mm complete as per manufacturer's specifications and direction of Engineer-in-charge | ITEM CODE 34 | ||
35 | 35 | i) Non Decorative finish | ITEM CODE 35 | 10.08 | M2 |
36 | 36 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions,at top, bottom & sides with with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/stainless steel screws including fixing all complete as per drawing & the directions of Engineer-in-charge. (Cost of glazing or panels to be paid for separately) | ITEM CODE 36 | ||
37 | 37 | i) Fixed Glazing with Powder coated aluminium (minimum thickness of powder coating 50 micron) sections | ITEM CODE 37 | 120 | KG |
38 | 38 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): | ITEM CODE 38 | ||
39 | 39 | ii) With float glass panes of 5.0 mm thickness (weight not less than 12.5kg/sqm) | ITEM CODE 39 | 5.4 | M2 |
40 | 40 | iii) With float glass panes of 8.0 mm thickness (weight not less than 20kg/sqm) | ITEM CODE 40 | 31.5 | M2 |
41 | 41 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. | ITEM CODE 41 | ||
42 | 42 | i) With stainless steel cover plate | ITEM CODE 42 | 3 | EA |
43 | 43 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per direction of Engineer in Charge complete Upto 5mm depth and 5mm width | ITEM CODE 43 | 50 | M |
44 | 44 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately). | ITEM CODE 44 | 8.06 | M2 |
45 | 45 | Structural steel work riveted,bolted or welded in built up sections, trusses & framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete: | ITEM CODE 45 | 1000 | KG |
46 | 46 | Providing & fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick MS sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3mm dia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standard drawing. | ITEM CODE 46 | 3 | EA |
47 | 47 | Providing & fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (minimum thickness of 5 mm) of approved make in all colours,shades except burgundy,bottle green,black of any size as approved by Engineer-in-Charge in skirting,risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade. | ITEM CODE 47 | 53.76 | M2 |
48 | 48 | Providing & laying Ceramic Glazed floor tiles 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours White, Ivory, Grey, Fume Red Brown, laid on 20mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) jointing with grey cement slurry@ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc. complete. | ITEM CODE 48 | 17.45 | M2 |
49 | 49 | Providing & laying vitrified floor tile in different sizes (thickness as per manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar as specified with coarse sand jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete for flooring/skirting as specified | ITEM CODE 49 | ||
50 | 50 | i) Flooring with size of Tiles 60x60Cm in cement mortar 1:4 | ITEM CODE 50 | 63.68 | M2 |
51 | 51 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, Single socketed pipes. | ITEM CODE 51 | ||
52 | 52 | ii) 110 mm diameter | ITEM CODE 52 | 28 | M |
53 | 53 | Providing and laying cement plaster on surfaces with Coarse sand including curing etc. | ITEM CODE 53 | ||
54 | 54 | i) 12mm Cement plaster of mix 1:4 (1 cement: 4 coarse sand) | ITEM CODE 54 | 127.92 | M2 |
55 | 55 | iii) 15mm cement plaster of mix 1:4 (1 cement: 4 coarse sand) on rough side of half or single brick wall | ITEM CODE 55 | 117.55 | M2 |
56 | 56 | Providing and laying 6mm thick cement plaster on surfaces with fine sand including curing etc. | ITEM CODE 56 | ||
57 | 57 | i) 6mm thick plaster of mix 1:3 (1 cement: 3 fine sand) | ITEM CODE 57 | 133.05 | M2 |
58 | 58 | Providing and applying plaster of Paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete | ITEM CODE 58 | 378.51 | M2 |
59 | 59 | Distempering with oil bound washable distemper of approved brand & manufacture to give an even shade with 2 or more coats including water thinnable priming coat with cement primer | ITEM CODE 59 | 260.96 | M2 |
60 | 60 | Finishing walls with Acrylic Smooth exterior paint of required shade (2 or more coat applied @ 1.67 ltr/10 sqm over & including priming coat of exterior Primer applied @ 2.20kg/10 sqm) | ITEM CODE 60 | 117.55 | M2 |
61 | 61 | Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint approved brand and manufacture over and including a priming of ready mixed zinc chromate yellow primer on 150mm dia pipes | ITEM CODE 61 | 28 | M |
62 | 62 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade with two or more coats over an under coat of suitable shade with ordinary paint of approved brand and manufacture. | ITEM CODE 62 | 50 | M2 |
63 | 63 | Lettering with black japan paint of approved brand & manufacture and (unit/letter/cm ht) | ITEM CODE 63 | 10 | EA |
64 | 64 | Demolishing cement concrete manually/ by mechanical means including disposal of material outside premises at an unobjectionable place as per direction of Engineer-in-charge. | ITEM CODE 64 | ||
65 | 65 | i) 1:3:6 or richer mix (i/c equivalent design mix) | ITEM CODE 65 | 5 | M3 |
66 | 66 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars & disposal of unserviceable material outside site to an unobjectionable place as/ direction of Engineer-in-charge | ITEM CODE 66 | 5 | M3 |
67 | 67 | Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge. | ITEM CODE 67 | 10 | M2 |
68 | 68 | Demolishing brick work manually/mechanical means including stacking of serviceable material & disposal of unserviceable material outside premises at an unobjectionable place as / direction of Engg-in-charge | ITEM CODE 68 | 10 | M3 |
69 | 69 | Construction of granular sub-base by providing close graded material conforming to specifications, mixing in a mechanical mixer plant at Optimum Moisture Content, carriage of mixed material by tippers to work site, for all lead and lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface & compacting with vibratory power roller to achieve the desired density, complete as per specification & direction of Engineer-in-charge. | ITEM CODE 69 | ||
70 | 70 | i) With material confirming to grade-I (size 75 mm to .075 mm) having CBR value - 30, Thickness as desired | ITEM CODE 70 | 196.5 | M3 |
71 | 71 | ii) With material confirming to grade-II (size 53 mm to .075 mm) having CBR value -25,Thickness as desired | ITEM CODE 71 | 196.5 | M3 |
72 | 72 | Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density). | ITEM CODE 72 | 393 | M3 |
73 | 73 | Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to .075 mm) to wet mix macadam (WMM) specifications including premixing the material with water at OMC for all leads and lifts, laying in uniform layers with mechanical paver finisher in sub-base/base course on well prepared surface and compacting with vibratory roller of 8 to 10 ton capacity to achieve the desired density, complete as per specifications & directions of Engineer-in- charge | ITEM CODE 73 | 462.5 | M3 |
74 | 74 | Providing & laying factory made reflective type Lacquered finish Grey / coloured pre-cast cement concrete, interlocking paver block of specified grade made by block making machine wih vibratory compaction & of approved size and design / shape, shade and manufacturers and as per IOCL's specifications. The paver blocks shall have peripheral chamfer, with average crushing strength as per IS 15658, maximum water absorption of 2% after 10 minutes and 5% after 24 hrs. as per BS 1881, maximum dimensional deviations of +/- 2mm on length @ width and +/- 3 mm on thickness. The job includes supplying and laying a layer of 50 mm thick clean coarse sand on thoroughly compacted sub-base below the paver blocks, cutting the paver blocks wherever required with hydraulic splitter, filling in the joints at the edges of paver blocks with sand, compacting with machine vibrator to required line and level, etc. complete. (Payment for provision of edge restraints shall be made separately) | ITEM CODE 74 | ||
75 | 75 | ii) M40 grade 80 mm thick reflective type Lacquered finish | ITEM CODE 75 | 1300 | M2 |
76 | 76 | Taking out existing CC interlocking paver blocks from footpath central verge, including removal of rubbish etc., disposal of unserviceable material out of site at unobjectionable place and stacking serviceable material within premises as per direction of Engineer - in-Charge | ITEM CODE 76 | 1300 | M2 |
77 | 77 | Laying Corporation supplied interlocking paver blocks of any design /shape laid in required line,level,curvature,colour & pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as/ direction of Engineer-in-charge. | ITEM CODE 77 | 1200 | M2 |
78 | 78 | Providing and fixing water closet squatting pan (Indian type W.C.pan) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C.flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required -White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. | ITEM CODE 78 | 1 | EA |
79 | 79 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white PVC flushing cistern including flush pipe with manually controlled device (handle lever),conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required: | ITEM CODE 79 | ||
80 | 80 | i) W.C. pan with ISI marked white solid plastic seat and lid | ITEM CODE 80 | 4 | EA |
81 | 81 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x 265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : | ITEM CODE 81 | ||
82 | 82 | i) One urinal basin with 5 litre white P.V.C. automatic flushing cistern | ITEM CODE 82 | 3 | EA |
83 | 83 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | ITEM CODE 83 | 3 | EA |
84 | 84 | Providing and fixing toilet paper holder : | ITEM CODE 84 | ||
85 | 85 | i) C.P. brass | ITEM CODE 85 | 4 | EA |
86 | 86 | Providing & fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : | ITEM CODE 86 | ||
87 | 87 | i) 100mm inlet & 100mm outlet SCI S&S as per IS - 3989. | ITEM CODE 87 | 6 | EA |
88 | 88 | ii) 100mm inlet & 75mm outlet SCI S&S as per IS - 3989. | ITEM CODE 88 | 2 | EA |
89 | 89 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank IS : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank | ITEM CODE 89 | 1000 | L |
90 | 90 | Providing and fixing PTMT bib cock of approved quality and colour. | ITEM CODE 90 | ||
91 | 91 | ii) 15 mm nominal bore, 122mm long. Weighing not less than 99 gms. | ITEM CODE 91 | 5 | EA |
92 | 92 | iii) 15 mm nominal bore, 165mm long. Weighing not less than 110 gms. | ITEM CODE 92 | 5 | EA |
93 | 93 | Providing and fixing PTMT pillar cock of approved quality and colour | ITEM CODE 93 | ||
94 | 94 | i) 15mm nominal bore, 107mm long. Weighing not less than 110 gms. | ITEM CODE 94 | 4 | EA |
95 | 95 | Providing and fixing PTMT, push cock of approved quality and colour. | ITEM CODE 95 | ||
96 | 96 | i) 15 mm nominal bore, 98mm long. Weighing not less than 75 gms. | ITEM CODE 96 | 4 | EA |
97 | 97 | Providing and fixing PTMT grating of approved quality and colour. | ITEM CODE 97 | ||
98 | 98 | i) Circular type,100 mm nominal dia | ITEM CODE 98 | 6 | EA |
99 | 99 | ii) Circular type 125 mm nominal dia with 25 mm waste hole | ITEM CODE 99 | 6 | EA |
100 | 100 | i) Inside dimensions 455x610mm and 45cm deep for single pipeline with common burnt clay FPS (non modular) bricks of class designation 7.5 | ITEM CODE 100 | 5 | EA |
101 | 101 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and SW drain pipe 100 mm diameter, 1.8 m long complete as per standard design with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 | ITEM CODE 101 | 1 | EA |
102 | 102 | Providing & laying water proofing treatment in sunken portion of WCs, bathroom etc. by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment & sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. | ITEM CODE 102 | 113.05 | M2 |
103 | 103 | CABLING AND ALLIED WORKS - ARMOURED CABLES Supply & laying of XLPE insulated PVC sheathed aluminium/copper conductor, 1.1 kV grade armoured cable conforming to IS:7098, as per approved make in ground/ trench/surface/pipe, etc. whereever required as per direction of Engineer In-charge. Note: The rate of Installation should be inclusive of Cable clamps, tags Saddles, Consumables etc. Trays/pipes, trenches, fabricated tray supports etc will be covered & paid in Separate Items | ITEM CODE 103 | ||
104 | 104 | iii) 3 Core x 1.5 sq. mm. (copper) | ITEM CODE 104 | 100 | M |
105 | 105 | CABLE TERMINATION GLANDS NON-FLP HEAVY DUTY DOUBLE COMPRESSION Cable Termination (NON FLP): Providing termination of 1.1 kV grade armoured cable for the following sizes including supply of NON FLP heavy duty Double Compresson cable glands, crimping type lugs and allied jointing materials, etc. all complete as per specification and direction of Engineer In-charge. Glands and lugs shall be of approved make. Copper lugs for copper cables and aluminium lugs for aluminium cables shall be used. | ITEM CODE 105 | ||
106 | 106 | vii) 3 Core x 2.5 sq. mm | ITEM CODE 106 | 5 | EA |
107 | 107 | CABLE JOINTING Cable Jointing : Providing straight through joint of following 1.1 KV grade XLPE insulated armoured cable with M-Seal make jointing kit, and other jointing material, etc. all complete including supply of all materials as per specification & direction of Engineer In-charge. | ITEM CODE 107 | ||
108 | 108 | vii) 3 Core x 2.5 sq. mm | ITEM CODE 108 | 5 | EA |
109 | 109 | ii) Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. | ITEM CODE 109 | 30 | EA |
110 | 110 | iii) Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. with modular switch, modular plate, suitable GI box | ITEM CODE 110 | 15 | EA |
111 | 111 | Supply and fixing of following Electrical fittings /fixtures | ITEM CODE 111 | ||
112 | 112 | i) 5 Amp Piano type switch | ITEM CODE 112 | 30 | EA |
113 | 113 | iii) 5 Amp Piano type 3 pin socket | ITEM CODE 113 | 10 | EA |
114 | 114 | iv) 15Amp modular type switch | ITEM CODE 114 | 3 | EA |
115 | 115 | v) 15Amp modular type 6 pin socket | ITEM CODE 115 | 3 | EA |
116 | 116 | SWITCHES, FUSES, MCBS, ELCBS ETC Supply and fixing of Modular switch frame with inner and outer face plates and accessories as per following details of approved including flush metal boxes/surface mounting boxes, plates, etc. all complete as per manufacturer's specification and direction of Engineer In-charge. | ITEM CODE 116 | ||
117 | 117 | iii) 4 module frame | ITEM CODE 117 | 4 | EA |
118 | 118 | iv) 6 module frame | ITEM CODE 118 | 4 | EA |
119 | 119 | vi) 12 module frame | ITEM CODE 119 | 3 | EA |
120 | 120 | xi) 2 Pin Telephone Modular Socket | ITEM CODE 120 | 3 | EA |
121 | 121 | xii) Fan Regulator of stepped modular type | ITEM CODE 121 | 3 | EA |
122 | 122 | Supplying and fixing of following MCBs with necessery inter connections on existing DB, Panel board etc. | ITEM CODE 122 | ||
123 | 123 | ii) Upto 32A DP MCB | ITEM CODE 123 | 2 | EA |
124 | 124 | Supply and fixing 3-pole MCCB of breaking capacity 16 KA in existing panel board. | ITEM CODE 124 | ||
125 | 125 | i) 32 Amp | ITEM CODE 125 | 4 | EA |
126 | 126 | ii) 63 Amp | ITEM CODE 126 | 3 | EA |
127 | 127 | SWITCH FUSE UNIT WITHOUT FUSE Supply & fixing switches/accessories in sheet metal enclosure including providing of required connections with supply of necessary cable/conduits as required in case of existing control switch panel/ switch board etc. all complete as per specification and direction of Engineer-In-Charge.( SFUs shall be of approved make and SFUs shall be without fuse) | ITEM CODE 127 | ||
128 | 128 | i) 16Amp SPN switch fuse unit | ITEM CODE 128 | 2 | EA |
129 | 129 | ii) 32Amp SPN switch fuse unit | ITEM CODE 129 | 2 | EA |
130 | 130 | iii) 16Amp TPN switch fuse unit | ITEM CODE 130 | 2 | EA |
131 | 131 | iv) 32Amp TPN switch fuse unit | ITEM CODE 131 | 2 | EA |
132 | 132 | v) 63Amp TPN switch fuse unit | ITEM CODE 132 | 3 | EA |
133 | 133 | MCB DISTRIBUTION BOARD INCLUSIVE OF SINGLE PHASE MCB Supply & fixing of MCB Distribution Board double door type, IP-42, inclusive of MCB, Single Phase, as per approved make of following types with all accessories such as tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs, etc. (MCB - 10KA Breaking Capacity) | ITEM CODE 133 | ||
134 | 134 | i) 8way DB with 32ADP as incoming-1No.& 6 to16A SP as outgoing-8Nos | ITEM CODE 134 | 1 | EA |
135 | 135 | Supply and Fixing of Discrete LED (Light Emitting Diode) Tube lights of 18 Watts with fittings and accessories, having IP65 protection class with Pressure Die Cast LM6/ADC12/LM24 housing and with toughened glass or UV stabilized polycarbonate cover type of approved make or equivalent as per direction of Engineer-in-charge. The LED driver shall have an in-built high voltage cutoff >= 290 V with power factor of complete fitting greater than 0.90. CCT (Correlated Colour temperature) shall be in the range of 5665 K +/- 355 K as per ANSI standard C78.377, CRI (Colour rendering index) should include all colour range from R1 to R15 and > 70 for outdoor luminaire. LED efficacy shall be greater than 140 lumens/watt @ 350mA drive current. The minimum system lumen efficacy of the luminaire shall be 100 Lumens per Watt. The Surge Protection Device (SPD) should be series type with fail safe, surge protection for minimum 3kV shall be provided. Supply of complete fitting with all accessories as per specification attached and as per direction of engineer in charge. Each lot of fittings shall accompany test certificates LM79/ IS:16106 and reference/ batch nos of LEDs and fittings for verification at site. The supply of LED lighting shall be covered by a warranty of minimum 60 months from the date of supply of the lighting and the LED light fitting shall be complete in all respects including LED, LED Driver, Electronic circuitory, Luminaire etc. | ITEM CODE 135 | 12 | EA |
136 | 136 | Supply and Fixing of Discrete LED (Light Emitting Diode) Tube lights of 8 Watts with fittings and accessories, having IP20 protection class with CRCA/PC/Aluminium Extrusion housing & with UV stabilized polycarbonate cover type of approved make or equivalent as per direction of Engineer in charge. The LED driver shall have an in-built high voltage cutoff >= 290 V with power factor of complete fitting greater than 0.90. CCT (Correlated Colour temperature) shall range from 5700 Kelvin (5665 K +/- 355 K) to 6500 Kelvin, CRI (Colour rendering index) should include all colour range from R1 to R15 and > 80 for indoor luminaire. LED efficacy shall be greater than 140 lumens/watt @ 350mA drive current. The minimum system lumen efficacy of the luminaire shall be 95 Lumens per Watt. The Surge Protection Device (SPD) should be series type with fail safe, surge protection for minimum 2kV shall be provided. Supply of complete fitting with all accessories as per specification attached and as per direction of engineer in charge. Each lot of fittings shall accompany test certificates LM79/ IS:16106 and reference/batch nos of LEDs and fittings for verification at site. The supply of LED lighting shall be covered by a warranty of minimum 60 months from the date of supply of the lighting and the LED light fitting shall be complete in all respects including LED, LED Driver, Electronic circuitory, Luminaire etc. | ITEM CODE 136 | 6 | EA |
137 | 137 | CEILING FANS Supply & fixing of ceiling fan for inside of the sales building of following type: | ITEM CODE 137 | ||
138 | 138 | iii) 1200 mm sweep | ITEM CODE 138 | 3 | EA |
139 | 139 | EXHAUST FANS Supply and fixing of exhaust fan including electrical wiring all shall be with per specification and direction of site In charge. The fans shall be with louvers / shutters. (The job does not include making suitable cut out in the wall for fixing the fan). | ITEM CODE 139 | ||
140 | 140 | iii) 12" heavy duty, make GEC or equivalent | ITEM CODE 140 | 2 | EA |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail