Military Engineer Services-MES has published Repair/ Rewinding/ Servicing Of Electric Motors/ Pump/ Repair/ Replacement Of Electric Panel And Allied Works Of Water Supply Installation At Af Stn Jodhpur Under Age E/M , Ge ( Af ) No 2 Jodhpur. Submission Date for this Tender is 07-11-2020. Electrical Maintenance Tenders in GE (AF) NO 2 JODHPUR Rajasthan. Bidders can get complete Tender details and download the document.
| Name of Work : REPAIR/ REWINDING/ SERVICING OF ELECTRIC MOTORS/ PUMP/ REPAIR/ REPLACEMENT OF ELECTRIC PANEL AND ALLIED WORKS OF WATER SUPPLY INSTALLATION AT AF STN JODHPUR UNDER AGE E/M, GE (AF) NO 2 JODHPUR | |||||
|---|---|---|---|---|---|
| Sl. No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Dismantling the pump set horizontal split casing type 1450 RPM of capacity 75 HP model DSM 100/36 Make Kirloskar overhauling the same by repair/replacing the defective parts as ordered, cleaning the inside of stator, rotor, varnishing and drying, re-erecting, aligning with the pump, testing and commissioning, including replacement of DE and NDE bearings, grease nipples, any other minor parts required for proper functioning, painting the motor with two coat of synthetic enamel paint after preparing the surface and replacement of worn out nut bolts, stud of gland capacity including making over size thread in the body for stud of gland capacity and provide the new stud of both side, replacement of gasket, gland packing, greasing of pump set etc complete, proper alignment with motor complete all as directed by Engineer-in-Charge.\n\nNote:- The spare part required for replacement shall be measured & paid as Supply only. | 4 | Each Job | |
| 2 | 1.01 | Supply only ball bearing DE + NDE (Make NBC/SKF | 4 | Each set | |
| 3 | 1.02 | Supply only Gun Metal bush | 8 | Each | |
| 4 | 1.03 | Supply only MS coupling set for pump & motor with pin | 4 | Each | |
| 5 | 1.04 | Supply only rubber star coupling. | 8 | Each | |
| 6 | 1.05 | Supply only stainless steel pump shaft with shaft key | 4 | Each | |
| 7 | 2 | Dismantling the pump set horizontal split casing type 1450 RPM of capacity 50 HP model DSM 100/36 Make Kirloskar overhauling the same by repair/replacing the defective parts as ordered, cleaning the inside of stator, rotor, varnishing and drying, re-erecting, aligning with the pump, testing and commissioning, including replacement of DE and NDE bearings, grease nipples, any other minor parts required for proper functioning, painting the motor with two coat of synthetic enamel paint after preparing the surface and replacement of worn out nut bolts, stud of gland capacity including making over size thread in the body for stud of gland capacity and provide the new stud of both side, replacement of gasket, gland packing, greasing of pump set etc complete, proper alignment with motor complete all as directed by Engineer-in-Charge.\n\nNote:- The spare part required for replacement shall be measured & paid as Supply only. | 6 | Each Job | |
| 8 | 2.01 | (a) Supply only ball bearing DE + NDE (Make NBC/SKF | 4 | Each set | |
| 9 | 2.02 | (b) Supply only Gun Metal bush | 8 | Each | |
| 10 | 2.03 | (c) Supply only MS coupling set for pump & motor with pin | 4 | Each | |
| 11 | 2.04 | (d) Supply only rubber star coupling. | 4 | Each | |
| 12 | 2.05 | (e) Supply only stainless steel pump shaft with shaft key | 2 | Each | |
| 13 | 3 | Taking out Centrifugal pump type DB 65/20. Make Kirloskar, RPM 2900, 30 HP from foundation by disconnecting suction & delivery pipe line, dismantling of pump, overhauling the same by repairing/replacing defective parts as ordered and reassembling, replacement of worn out nuts, bolts, repairing of bearing housing complete incl greasing and making connection complete all as directed. | 2 | Each Job | |
| 14 | 3.01 | Material only bronze impeller with neck ring. | 5 | Each | |
| 15 | 3.02 | Material only ball bearing DE + NDE (Make NBC/SKF) | 5 | Each Set | |
| 16 | 3.03 | (c) Material only Gun Metal bush. | 5 | Each | |
| 17 | 3.04 | (d) Material only MS gland cap. | 2 | Each | |
| 18 | 3.05 | (e) Material only rubber bush/star coupling. | 5 | Each | |
| 19 | 3.06 | (f) Material only MS coupling set with pin. | 2 | Each set | |
| 20 | 4 | All as per item No 3 above but type DB 80/32 Make Kirloskar, RPM 1450, 10 HP. | 10 | Each Job | |
| 21 | 4.01 | Material only stainless steel shaft with shaft key. | 9 | Each | |
| 22 | 4.02 | Material only bronze impeller with neck ring. | 10 | Each | |
| 23 | 4.03 | Material only ball bearing DE+ NDE (Make NBC/SKF) | 9 | Each Set | |
| 24 | 4.04 | Material only Gun Metal bush. | 8 | Each | |
| 25 | 4.05 | Material only MS gland cap. | 5 | Each | |
| 26 | 4.06 | Material only rubber bush/star coupling. | 8 | Each | |
| 27 | 4.07 | Material only MS coupling set with pin. | 8 | Each set | |
| 28 | 5 | All as per item No 3 above but cap 20 HP, RPM 1450, Make Kirloskar, DB 80/32 | 5 | Each Job | |
| 29 | 5.01 | Material only bronze impeller with neck ring. | 2 | Each | |
| 30 | 5.02 | (b) Material only ball bearing DE + NDE (Make NBC/SKF) | 2 | Each Set | |
| 31 | 5.03 | (c) Material only Gun Metal bush. | 5 | Each | |
| 32 | 5.04 | (d) Material only star coupling. | 2 | Each | |
| 33 | 5.05 | (e) Material only MS coupling set with pin. | 2 | Each set | |
| 34 | 6 | All as per item No 3 above but cap 20 HP, RPM 2900, Make Kirloskar, type RKB14/40H | 5 | Each Job | |
| 35 | 6.01 | (a) Material only bronze impeller with neck ring. | 2 | Each | |
| 36 | 6.02 | (b) Material only ball bearing DE + NDE (Make NBC/SKF) | 2 | Each Set | |
| 37 | 6.03 | (c) Material only Gun Metal bush. | 5 | Each | |
| 38 | 6.04 | (d) Material only star coupling. | 2 | Each | |
| 39 | 6.05 | (e) Material only MS coupling set with pin. | 1 | Each set | |
| 40 | 7 | All as per item No 3 above but cap 12.5 HP, RPM 2900/1450 RPM , Make Kirloskar. | 2 | Each Job | |
| 41 | 7.01 | (a) Material only ball bearing DE + NDE (Make NBC/SKF) | 2 | Each Set | |
| 42 | 7.02 | (b) Material only bronze impeller with neck ring. | 2 | Each | |
| 43 | 7.03 | (c) Material only Gun Metal bush. | 3 | Each | |
| 44 | 7.04 | (d) Material only MS gland cap | 3 | Each | |
| 45 | 7.05 | (e) Material only rubber bush/star coupling. | 3 | Each Set | |
| 46 | 7.06 | (f) Material only MS coupling set with pin. | 3 | Each set | |
| 47 | 8 | All as item No 3 above but 15 HP, 1450 RPM Make – Kirloskar | 5 | Each Job | |
| 48 | 8.01 | (a) Supply only stainless steel shaft with shaft key. | 5 | Each | |
| 49 | 8.02 | (b) Supply only ball bearing DE + NDE (Make NBC/SKF | 3 | Each set | |
| 50 | 8.03 | (c) Supply only bronze impeller with neck ring | 5 | Each | |
| 51 | 8.04 | (d) Supply only Gun Metal bush | 2 | Each | |
| 52 | 8.05 | (e) Supply only MS coupling set for pump & motor with pin | 4 | Each set | |
| 53 | 8.06 | (f) Supply only star coupling. | 2 | Each | |
| 54 | 8.07 | (g) Supply only gun metal guide bush | 4 | Each | |
| 55 | 9 | All as per item No 3 above but cap 7.5 HP . | 5 | Each | |
| 56 | 9.01 | Supply only ball bearing DE + NDE (Make NBC/SKF | 3 | Each Set | |
| 57 | 9.02 | Supply only bronze impeller with neck ring. | 4 | Each | |
| 58 | 9.03 | Supply only water seal | 3 | Each | |
| 59 | 9.04 | M&L for rewinding the motor stator with super enameled copper wires of suitable gauge & class of insulation including insulation paper, sleeves, thimbles etc and testing complete. | 3 | Each | |
| 60 | 9.05 | Supply only PVC cooling fan as per sample. | 2 | Each | |
| 61 | 9.06 | Supply only connection plate bakelite for motor as per sample. | 2 | Each Job | |
| 62 | 10 | All as per item No 3 above but cap 5 HP. | 2 | Each Job | |
| 63 | 10.01 | (a) Material only ball bearing DE+ NDE (Make NBC/SKF) | 2 | Each Set | |
| 64 | 10.02 | (b) Material only bronze impeller with neck ring. | 2 | Each | |
| 65 | 10.03 | (c) Material only water seal | 2 | Each | |
| 66 | 10.04 | (d) M & L for rewinding the motor stator with super enameled copper wires of appropriate gauge, class of insulation, including insulation paper, sleeves, thimbles etc complete | 4 | Each Job | |
| 67 | 11 | All as per item No 3 above but cap 3/2 HP. | 4 | Each Job | |
| 68 | 11.01 | (a) Material only ball bearing DE+ NDE (Make NBC/SKF) | 2 | Each Set | |
| 69 | 11.02 | (b) Material only bronze impeller with neck ring. | 2 | Each | |
| 70 | 11.03 | (c) Material only water seal | 2 | Each | |
| 71 | 11.04 | (d) M & L for rewinding the motor stator with super enameled copper wires of appropriate gauge, class of insulation, including insulation paper, sleeves, thimbles etc complete | 4 | Each Job | |
| 72 | 12 | Taking out the centrifugal (monoblock) pump set cap 1/0.5 HP, single phase 240 volts from foundation including disconnecting electric connection , suction/ delivery pipe line, dismantling the pump & motor, overhauling the same by repairing/replacement defective parts as ordered and reassembling incl replacement of worn out nut bolts, washers, studs, gasket, gland packing including repairing to bearing housing of pump and motor, greasing of pump and reinstalling at site and making connection and testing complete.\n\nNote: The spare part required for replacement shall be measured and paid as material only. | 4 | Each Job | |
| 73 | 12.01 | (a) Material only ball bearing DE + NDE (Make NBC/SKF) | 8 | Each Set | |
| 74 | 12.02 | (b) Material only water seal. | 4 | Each | |
| 75 | 12.03 | (c) Material only rotor assembly. | 4 | Each | |
| 76 | 12.04 | (d) M & L for rewinding the motor stator with super enameled copper wires of appropriate gauge class of insulation, installation paper, sleeves, thimbles etc complete | 5 | Each Job | |
| 77 | 13 | Taking out the submersible pump set 5 HP 3 phase 415 volts, 50 c/s AC supply alongwith column pipe 50 mm dia/80 mm dia (approx 40 RM) from the bore well by disconnecting electric connection , dismantling of pump and motor, overhauling the same by repairing/replacement defective parts as ordered and reassembling incl replacement of worn out nut bolts, washers, complete and lowering the same after repair and making connection complete all as directed .\n\nNote: The spare part required for replacement shall be measured and paid separately as supply only. | 3 | Each Job | |
| 78 | 13.01 | (a) Material only stainless steel pump shaft. | 2 | Each | |
| 79 | 13.02 | (b) Material only PVC impeller with key. | 2 | Each | |
| 80 | 13.03 | (c) Material only jointing kit for submersible pump. | 2 | Each | |
| 81 | 13.04 | (d) Rewinding the stator with super enameled copper wires of appropriate gauge and class of insulation including insulation paper, sleeves, thimbles etc and testing complete. | 2 | Each Job | |
| 82 | 13.05 | (e) Material only rubber gasket 3mm thick having 04 Nos of 5/8” dia holes. | 2 | Each | |
| 83 | 13.06 | (f) Material only shaft bush. | 2 | Each | |
| 84 | 13.07 | (g) Material only thrust bearing of pump set Make NBC/SKF. | 4 | Each | |
| 85 | 13.08 | (h) Material only suction strainer. | 4 | Each | |
| 86 | 14 | All as per item No 13 above but capacity 7.5/10 HP. | 5 | Each Job | |
| 87 | 14.01 | (a) Material only threaded pin for hold the valve spring. | 2 | Each | |
| 88 | 14.02 | (b) Material only Gun Metal impeller with key. | 2 | Each | |
| 89 | 14.03 | (c) Material only jointing kit for submersible pump. | 5 | Each | |
| 90 | 14.04 | (d) Rewinding the stator with super enameled copper wires of appropriate gauge and class of insulation including insulation paper, sleeves, thimbles etc and testing. | 5 | Each Job | |
| 91 | 14.05 | (e) Material only studs. | 10 | Each | |
| 92 | 14.06 | (f) Material only bearing bush. | 6 | Each | |
| 93 | 14.07 | (g) Material only thrust bearing of pump set Make NBC/SKF. | 6 | Each | |
| 94 | 14.08 | (h) Material only stage casing with integral defuser. | 8 | Each | |
| 95 | 15 | All as per item No 13 above but capacity 12.5/15 HP. | 2 | Each Job | |
| 96 | 15.01 | (a) Material only stainless steel pump shaft. | 2 | Each | |
| 97 | 15.02 | (b) Material only Gun Metal impeller with key. | 3 | Each | |
| 98 | 15.03 | (c) Material only jointing kit for submersible pump. | 2 | Each | |
| 99 | 15.04 | (d) Rewinding the stator with super enameled copper wires of appropriate gauge and class of insulation including insulation paper, sleeves, thimbles etc and testing. | 2 | Each Job | |
| 100 | 15.05 | (e) Material only Oil seal and O ring | 5 | Each | |
| 101 | 15.06 | (f) Material only bearing bush upper & lower . | 2 | Each | |
| 102 | 15.07 | (g) Material only thrust bearing of pump set Make NBC/SKF. | 2 | Each | |
| 103 | 15.08 | (h) Material only finger pressure disc. | 4 | Each | |
| 104 | 16 | All as per item No 13 above but capacity 20 HP. | 2 | Each Job | |
| 105 | 16.01 | (a) Material only balancing ring of rotor. | 2 | Each | |
| 106 | 16.02 | (b) Material only Gun Metal impeller with key. | 8 | Each | |
| 107 | 16.03 | (c) Material only jointing kit for submersible pump. | 2 | Each | |
| 108 | 16.04 | (d) Rewinding the stator with super enameled copper wires of appropriate gauge and class of insulation including , insulation paper, sleeves, thimbles etc and testing. | 2 | Each Job | |
| 109 | 16.05 | (e) Material only rubber gasket 3mm thick having 04 Nos of 5/8” dia holes. | 10 | Each | |
| 110 | 16.06 | (f) Material only shaft bush. | 2 | Each | |
| 111 | 16.07 | (g) Material only thrust bearing of pump set Make NBC/SKF. | 2 | Each | |
| 112 | 17.01 | Taking out electric motor AC 3 phase 415 volts from foundation, taken to work shop, dismantling the motor, taking out old burnt wiring, cleaning the starter slots, material and labour for rewinding the stator with appropriate gauge super enameled copper wire and installation paper, sleeves, thimbles etc, complete varnishing and backing up the windings, repairs to bearing housings, replacing the bearings, cooling fan and connection plate, taking back to site, fixing on foundation making electric connection, realigning with pump/motor and testing complete of following size :- (a) 75 HP Cap. | 2 | Each Job | |
| 113 | 17.02 | (b) 50 HP Cap. | 3 | Each Job | |
| 114 | 17.03 | (c) 30 HP Cap. | 2 | Each Job | |
| 115 | 17.04 | (d) 20 HP Cap. | 4 | Each Job | |
| 116 | 17.05 | (e) 10 HP Cap. | 4 | Each Job | |
| 117 | 18 | Taking out old exiting Pressure booster pump of Capacity 1.5/2 HP by disconecting the pipe line from the existing pressure tank and electric connections. Checking all components by replacement of the fualty parts at the site including refitting the same for proper busting system by switching device and testing complete all as specified and directed by Engineer-in-charge. \n\nNote: The spare part required for replacement shall be measured and paid separately as supply only. | 2 | Each Job | |
| 118 | 18.01 | (a) Material only five way connector as per existing size | 2 | Each | |
| 119 | 18.02 | (b) Material only Pressure Switch. | 2 | Each | |
| 120 | 18.03 | (c) Material only PVC conecting pipe heavy duty. | 3 | Each | |
| 121 | 18.04 | (d) Material only gun metal non return valve of 15 mm dia suitable for pressure pump. | 2 | Each | |
| 122 | 18.05 | (e) Material only base plate. | 2 | Each | |
| 123 | 19 | Supply and fix in repair flanged GI pipe medium grade 80mm bore (as suction line of pump) including cutting threading welding of flange etc with GI fitting such as bend, flange, reducers etc including taking out old existing suction line. | 20 | RM | |
| 124 | 20 | Supply and fix in repair foot valve made out of GI/CI (ISI marked) of 80/100 mm dia Make- Kirloskar/ Normex | 6 | Each | |
| 125 | 21 | Supply and fix in repair foot valve made out of GI/CI (ISI marked) heavy duty of 150 mm dia Make- Kirloskar/Normex. | 4 | Each | |
| 126 | 22 | Supply, installation, testing & commissioning in repair CI sluice valve CI body double flanged ends with brass spindle and nut class – PN- 1.6 (ISI marked) incl all jointing material and nut, bolts and dismantling the old existing sluice valve and making good the disturbed surface matching with existing surface of size 150mm bore. Make – Kirloskar/Khejriwal/Upadhyay. | 4 | Each Job | |
| 127 | 23 | Taking out the existing suction line of 150mm dia and replacent with new from the sump approx 7 mtr including foot valve and closing the hole of walls. | 10 | Each Job | |
| 128 | 24 | Supply and fix in repair the suction line made out of flanged 150mm dia GI pipe medium grade (ISI marked) with flange, bend, nut-bolt, rubber packing incl cutting, welding, threading making piece as per site requirement all as directed by Engr-in-Charge, making entrance on the roof of sump complete incl fixing the foot valve retrieved from item No 20 above testing complete. | 50 | RM | |
| 129 | 25 | Supply and fix in repair flange GI suitable for 150/80 mm dia including welding to GI fitting as per ground requirement. | 10 | Each Job | |
| 130 | 26 | Repairs to fully automatic oil immersed star delta starter of range 7.5 HP to 30 HP by dismantling from the existing panel and replacing of burnt no volt coil ,relay , contact Kit , wire of existing size including top up of transformer oil etc and refing after repair/replacement all as per site requirement. | 2 | Each Job | |
| 131 | 27 | S&F in repairs fully automatic oil immersed star delta starter suitable for relay range 6 to 10 Amps ,coil -380 volt in sheet steel enclosure for AC 3 phase supply 415 V 50 Hz, 10 HP motor . Make - Bentex or equivalent to Jyoti | 2 | Each | |
| 132 | 28 | All as per item No 27 but suitable for relay range 20 to 32 Amps ,coil -380 volt of capacity 25 HP pump set Make - Bentex or equivalent to Jyoti | 2 | Each | |
| 133 | 29 | M & L in CSXi soft starter suitable for motor 55 KW with standard applications , inbuilt bypass contactor, soft start/stop/adjustable current limit including motor protection against over load, single phasing , phase sequence reversal , abnormality in supply connected as per site requirement complete all as specified and as directed by Engineer-in-Charge. Cat Part No - CSXi 055V4C1 Make - L&T / schinender or equivalent to Siemens /ABB/HPL | 1 | Each | |
| 134 | 30 | Material and labour in repair for over hauling/ lubrication emtork actuator valves Model No : M1/030/A and M0/030/E including replacement of unserviceable spare parts at CPH area make Marsh, three phase, TEFC type motor, DOl starting complete entire satisfaction of Engr in charge.\n\nNote- defective spare parts for the above will be measured and paid separately under Sl items | 2 | Each Job | |
| 135 | 30.01 | (a) Supply only actuator stroke( Stainless Steel spindle 2.4 mtr long). Make – as per sample. | 2 | Each | |
| 136 | 30.02 | (b). Supply only coupling piece . Make as per sample. | 3 | Each | |
| 137 | 30.03 | (c) Supply only spur gear Box . make as per sample. | 3 | Each | |
| 138 | 30.04 | (d) Supply only Torque switch. make as per sample. | 2 | Each set | |
| 139 | 30.05 | (e) Supply only Travel switches.make as per sample. | 2 | Each | |
| 140 | 30.06 | (f) Supply only torque switch operating cam.make as per sample. | 2 | Each | |
| 141 | 30.07 | (g) Supply only locking plate.make as per sample. | 2 | Each | |
| 142 | 30.08 | (h) Supply only Eccentric pins.make as per sample. | 10 | Each | |
| 143 | 30.09 | (j) Supply only Allen bolts- M8x100L. make as per sample. | 10 | Each | |
| 144 | 31 | S&F in repairs fully automatic air break star delta starter in sheet steel enclosure with single phase protection suitable for AC 3 phase supply 415 V 50 Hz, 25 HP motor relay range 12 -21 Amps. Make - L&T cat part No -SS91855 or equivalent to Siemens/ABB/HPL | 2 | Each | |
| 145 | 32 | S&F in repairs fully automatic air break star delta starter in sheet steel enclosure with single phase protection suitable for AC 3 phase supply 415 V 50 Hz, 15 HP motor relay range Amps Make - L&T cat part No -SS90705 or equivalent to Siemens/ABB/HPL | 3 | Each | |
| 146 | 33 | Repair/Replacement for Power contactors 4 pole, 400 Amps conform to IS /IEC 60947 range upto 80 Amps with aux contacts 2 No+ 2 NC . Type -MNX 70 Cat part No - LC1F5004 Make L&T /HPL/Schneidar or equivalent. | 4 | Each | |
| 147 | 34 | S&F in repairs single phase priventer suitable for 3 pahse 415 volt 50 HZ AC Make - MINILEC or eqivalent | 15 | Each | |
| 148 | 35 | Earthing complete with galvanized steel earth plate electrode 60 cmrx600 cmx6.3 mm thick buried directly in ground (Earth pit less than 4 mtr deep below normal ground level with top edge of the plate not less than 1.5 mtr below normal ground level) with top edge of the plate not less than 3.25 mtr below normal ground level connected to aluminium earth lead 25x4 mm up to 7.5 mtr length by means of GI bolt, nuts, check nuts and washers of aluminium strip at least two places. Earth pit surrounded by picked layers of coal dust and common salt 15 cm thick all around bottom sides and top and watering pipe 20 mm bore of GI medium grade with funnel all as shown in electrical plate No 5 of SSR part I and connecting to earthing test point including earth test point and testing on completion including CI cover frame and PCC (1:3:6) type C.2 using 20 mm graded stone aggregate as in earthing pit with CI cover and framing including necessary excavation of earth work in hard dense soil/rock complete all as specified. \n | 8 | Each | |
| 149 | 36 | Supply and fixing MCCB in replacement of 63 Amps , 3 pole, 415 volts, 50 Hz, rupturing capacity 16 KA, connection with proper size of thimbles complete including taking out defective/unserviceable MCCB all as specified and directed. | 3 | Each | |
| 150 | 36.01 | Ditto, but 100 Amps, 16 KA | 3 | Each | |
| 151 | 37 | Supply and fix MCCB in replacement with thermal magnetic release adjustable type DU 160, 125A 16 KA , 415 volts 3 pole all as specified & directed. | 2 | Each | |
| 152 | 38 | Supply and fix MCCB in replacement with thermal magnetic release adjustable type DU 160, 160A 36 KA , 415 volts 3 pole all as specified & directed. | 2 | Each | |
| 153 | 38.01 | Ditto, but 200 Amps, 36 KA | 3 | Each | |
| 154 | 39 | Supply and fix MCCB in replacement with thermal magnetic release adjustable type, DN2-250D, 250A , 415 volts 4 pole 36 KA all as specified & directed. | 4 | Each | |
| 155 | 40 | Supply and fix MCCB in replacement with thermal magnetic release adjustable type, DN3-400D, 400A , 415 volts 4 pole 36 KA all as specified & directed. | 2 | Each | |
| 156 | 41 | Supply, install, testing and commissioning in replacement of outdoor type factory made ,CRCA Sheet, thickness 3.15 mm CPRI test certified, platform mounted LT panel board to accomodate the following items and built upon angle iron frame suitable size compartmentalized design work, duly powder coated with gray paint and suitable size of cable glands chromium plated and Aluminium busbars TPN, 400 Amps,415 V,50 Hz complete as following :- \n(i) MCCB 200 Amps, 4 Poles, 25 kA-01 (Incoming) \n(ii) MCCB 63 Amps, 3 Poles, 16 kA - 05 No (Outgoing) \n (iii) Volt meter 0 - 500 V digital type with selector switch - 1 No (iv) Amp meter 0 - 200 A digital type with selector switch - 1 No (v) Indicating lamp LED RYB set of three with colour codeing - 1 No. \n(vi) CT of ratio 200/5 Amp - 01 Set\n(vii) Change over switch 200 Amps -01 No. | 2 | Each Job | |
| 157 | 42 | Excavation in trenches in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5m depth, getting out the excavated earth, forming bottom surfaces to required gradient complete all as specified and directed by Engineer-in-Charge. | 186.3 | Cum | |
| 158 | 43 | Removal of excavated material soils to a distance n exc 50 m and depositing where directed at a level not exceeding 1.5m above the straight point | 70 | Cum | |
| 159 | 44 | Returning filling in, including spreading, levelling watering and well ramming in layers n exc 25 cm as in any type of soil. | 116.3 | Cum | |
| 160 | 45 | Material and labour for sand cushioning using dry and clean tibba sand in two layers, first layers of 80mm thick before laying of cable and second layer of 150mm thick after laying of cable in trenches/ducts including consolidation of each layers complete all as specified and directed. | 62.1 | Cum | |
| 161 | 46 | M&L for stone slab 30-50 mm thick rough dressed jodhpur stone patties/slab cover in trenches for ptotection of cable 25 to 30 cm wide tnd thickness not less than 50 mm in length lay dry abutting each other with gap between adjacent slab not exceeding 10 mm over sand cushioning. | 193.2 | Sqm | |
| 162 | 47.01 | Taking out defective cable XLPE/PVC sheathed 1100 volt grade heavy duty armoured with aluminium conductor from trenches, shifting serviceable cable for relaying or taking the unserviceable cable as credit complete all as specified and directed for the following:-.Note : Excavation and earth work shall be measured and paid for separately (a). 4 core 16 Sqmm | 100 | RM | |
| 163 | 47.02 | (b). 3.5 core 25 Sqmm | 150 | RM | |
| 164 | 47.03 | (c). 3.5 core 35 Sqmm | 130 | RM | |
| 165 | 47.04 | (d). 3.5 core 50 Sqmm | 150 | RM | |
| 166 | 47.05 | (e). 3/3.5 core 95 Sqmm | 140 | RM | |
| 167 | 47.06 | (f). 3.5 core 120 Sqmm | 150 | RM | |
| 168 | 48 | Supplying, laying, jointing and testing of under ground cable XLPE insulated, 1100 volt grade heavy duty armoured with stranded aluminium conductor 4 core 16 Sqmm laid in trenches/duct/pipe including all electrical connection with required lugs and nuts, bolts complete all as specified and directed by Engr-in-Charge | 100 | RM | |
| 169 | 48.01 | ditto size 3.5 core 25 Sqmm. | 100 | RM | |
| 170 | 48.02 | ditto but size 3.5 core 35 Sqmm. | 150 | RM | |
| 171 | 48.03 | ditto but size 3.5 core 50 Sqmm. | 150 | RM | |
| 172 | 48.04 | ditto but size 3.5 core 95 Sqmm. | 140 | RM | |
| 173 | 48.05 | ditto but size 3.5 core 120 Sqmm. | 150 | RM |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
