|
tender for addition alterations to omqs at af stn high ground.; 1 building works 2 dismantling bricks tiles or concrete tiles single layer on roofs and removal, complete all as specified. 3 demolition of mud phuska on roofs any thickness including mud plastering (whether full thickness removed or only a part thereof) and removal to a distance exceeding 100 metre, complete all as specified 4 material & labour roughening of surfaces of old concrete floor/slab by wire brushing, sweeping, cleaning and washing down to remove all loose dust etc, and brushing neat cement slurry @ 3.00 kg/square metre on floor/roof surface, complete all as specified. 5 material & labour plain cement concrete (1:2:4) type b-1, using 20 mm graded mechanically crushed stone aggregates as in padding to maintain the required slope and finished the surface even and smooth without using extra cement, complete all as specified. 6 material and labour for cleaning the new or old pastered or concrete surfaces and water proofing treatment of roof horizontal surfaces consisting as under:- (a) applying evenly a coat of bituminous primer conforming to is-3384:1986 @ 0.30 litre/sqm including preparation of roof surfaces(b) a layer of minimum 3mm thick app polymeric membrane of weight not less than3.60 kg/sqm, reinforced with polyester non-woven fabric (weight not less than 160gm/sqm), duly sealed at over laps & joints with flame (by torch application) all as per manufacturer’s instructions, complete all as specified and directed.(c) finally finished with a coat of bitumastic aluminium paint over the membrane . 7 material and labour for cleaning the new or old pastered or concrete surfaces and water proofing treatment on vertical surfaces of roof consisting as under including taking down old membrane( as in vertical surfaces ):- (a) applying evenly a coat of bituminous primer conforming to is-3384:1986 @ 0.30 litre/sqm including preparation of roof surfaces(b) a layer of minimum 3mm thick app polymeric membrane of weight not less than3.60 kg/sqm, reinforced with polyester non-woven fabric (weight not less than 160gm/sqm), duly sealed at over laps & joints with flame (by torch application) all as per manufacturer’s instructions, complete all as specified and directed.(c) finally finished with a coat of bitumastic aluminium paint over the membrane. 8 material & labour 40 mm thick brick tiles laid on roof and including 15 mm thick screed bed in cm (1:4) and jointed grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement over andcomplete all as specified and directed. 9 material & labour for brick tiles (old retreived tiles shall be reusd after cleaning) laid on roof and including 15 mm thick screed bed in cm (1:4) and jointed grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement over andcomplete all as specified and directed. note : the cost of cleaning and washing of brick tiles for re use shall be deemed to be included in the unit rate quoted by the tenderer. 10 m&l flush pointing to brick laid flat or brick tiles in roof in cm 1:3 complete all as specified and directed by engr in chage 11 dismantling pvc water storage tank of capacity exceeding 250 litre but not exceeding 500 litre and stacking for issuing under credit, complete all as specified. 12 dismantling water tanks exc 500 but n. exc. 1000 capacity in ltr and removing from site, complete all as specified and directed. 13 m&l rotational moulded pvc, double layered, white colour water storage tanks of capacity 500 litre (cylindrical vertical with closed top), isi marked, hoisted and fixed in position, with & including all fittings such as gi tank nipple etc. but excluding ball valve, complete all as specified. 14 fixing only rotational moulded pvc, double layered, white colour water storage tanks of capacity 500 litre hoisted and fixed in position, with & including new fittings such as gi tank nipple etc. but excluding ball valve, complete all as specified.note:-old retrieved water tank will be reused after thorough cleaning and the cost of cleaning is deemed to be inclusive in the unit rate quoted. 15 m&l rotational moulded pvc, double layered, white colour water storage tanks of capacity 1000 litre (cylindrical vertical with closed top), isi marked, hoisted and fixed in position, with & including all fittings such as gi tank nipple etc. but excluding ball valve, complete all as specified. 16 m&l in repairs ball valve, high pressure of ptmt with epoxy coated aluminium rod and high density plastic ball, isi marked (minimum weight 210 gms), screwed & suitable for iron pipe 20 mm bore,complete all as specified. 17 s/f in repairs 20mm gun metal,globe or gate valve, with iron wheel head screwed both ends for iron pipe and fixed complete 18 s/f in repairs 15mm gun metal,globe or gate valve, with iron wheel head screwed both ends for iron pipe and fixed complete 19 dismantling floor, health or wall tilling including cement mortar bedding (but not backing removing survicabletiles to store and rubbish off the primises complete all as specified and directed. 20 m&l for 25 mm thick, pcc (1:2:4), type b-0 (12.5mm graded crushed stone aggregate) as in flooring finished even & rough to receive the bedding mortar, complete all as specified. 21 m&l for 40 mm thick, pcc (1:2:4), type b-1 (20 mm graded crushed stone aggregate) as in flooring finished, complete all as specified 22 m&l first quality, non skid ceramic coloured tiles, 7 to 8 mm thick, joint free (square/ rectangular) area of each tile exceeding 0.11 sq.m but not exceeding 0.18sq.m, laid in floors with neat cement slurry @ 3.00 kg/square metre over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified. 23 m & l forglazed ceramic (digital glossy finish) coloured tiles 350x450x7-8 mm thick, joint freeon vertical surfaces, set and jointed in neat cement slurry and pointed in white/colour cement to match over and including 15mm thick cement mortar as in backing coat of tile in cement mortar 1:4, complete all as specified and directed by engineer-in-charge. 24 m & l for double charged vitrified ceramic coloured tiles, 10 mm thick (square/ rectangular) area of each tiles exceeding 0.36 sq.m, but n.exc 0.42 sqm laid in floors with neat cement slurry @ 3.00 kg/square metre over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified. 25 m & l for double charged vitrified ceramic coloured tiles, 10 mm thick (square/ rectangular) area of each tileexceeding 0.36 sq.m, but .exc 0.42 sqm as in skirting, set and jointed in neat cement slurry, over and including 10 mm thick rendering of cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified. 26 demolition stone slabs and tiles of any description or thickness in floors/ dado, aprons etc., laid bedded and pointed in any mortar, complete all as specified. 27 m & l for granite (of any type ) 20 mm thick, work (table rubbed and polished) fine grained z black/red incooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed bed of 15 mm thick in cm 1:4, complete all as specified. 28 s&f in repairs vitreouschina wash down water closet (pedestal pattern), white (excluding fixing bolts flushing cistern and flush pipe) including connected to drains outlet, complete all as specified and directed by engineer - in -charge. 29 s&f in repairs vitreous china squating pan, orissapattern, size 580x440mm white, with integral foot rests, including 100mm cast iron p or s trap and 100mm cast iron sanitary connection socket to fit wc outlet including connection to trap, to flushing pipe, anti-syphonage pipe etc. complete including making good to floor complete all as specified and directed. 30 s&f in repairs hand shower (health foucet) cast copper alloy chromium plated with and including 8mm dia 1.00 meter long pvc flexible tube and with hook complete all as specified and directed. 31 s & f in repairs 10 litres capacity, pvc valve less, syphonic action type,flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and suitable flush pipe pvc 32mm dia complete all as specified and directed. 32 s&f in repair for pvc connections 15mm size with ptmt nuts of length 600mm complete all as specified and directed. 33 s & f in repairs angle cock, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15 mm bore iron pipe or for brass ferrule complete all as specified. 34 s&f in repairs bib cock long body with flange, cast copper alloy, chromium plated, fancy type, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule and fixed in repairs, complete all as specified. 35 s&f in repairs bib cock long body with flange, cast copper alloy, chromium plated, fancy type, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule suitable for washing machine connection ( with nozzle) complete all as specified. 36 taking up or down 15 mm bore steel tubing with connections or fittings from wall, ceiling, and floor etc., including removal from site, complete all as specified. 37 taking up or down 20 mm bore steel tubing with connections or fittings from wall, ceiling, and floor etc., including removal from site, complete all as specified. 38 s & f 15mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed.note : cutting chases as required shall be measured and paid seperately. 39 s&f steel water tubes, 20 mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors, complete all as specified. 40 re-fixing steel water tubing of 15 mm bore, with all fittings at new or old position, laid in floor along wall or at ceiling, complete all as specified. 41 re-fixing steel water tubing of 20 mm bore, with all fittings at new or old position, laid in floor along wall or at ceiling, complete all as specified. 42 cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exc 10 cm girth in brick walls complete all as specified and directed. 43 s&f door seal 50mm wide and 1 m in lenth built in aluminium black plate with nylon brush fixed with screws, complete all as specified. 44 s&f in repairs wash basins, vitreous china, white, rectangular type of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, over and including new bracketscomplete all as specified and directed. 45 s&f in repair pvc waste pipe flexible for sink/ whb of 32mm size complete all as specified and directed by engineer-in-charge. 46 s & f in repair 15mm dia brass cp central hole basin mixer with 450mm braided connection pipe (without pop-up) for mixing hot & cold water fixed in repairs,complete all as specified and directed by engineer-in-charge.(make: cat no. 8850 of prayag or equivalent in parryware/cera/ marc sanitation) 47 s&f in repair wall mixer with l bend (provision for over head shower), cast copper alloy, chromium plated for mixing hot and cold water, screwed down for 15mm bore iron pipe, fixed in repair complete all as specified and directed. (make: cat no. 8675 of prayag or equivalent in parryware/cera/ marc sanitation) 48 s & f in repair 15mm dia brass cp sink mixer (wall mounted) for mixing hot & cold water fixed in repairs, complete all as specified and directed by engineer-in-charge. ( make: cat no. 8855 of prayag or equivalent in parryware/cera/ marc sanitation) 49 s&f in repair rectangular sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed with pvc rawl plugs and wooden screws as fixed in repairs, complete all as specified and directed. 50 s&f in repair corner glass shelf of radius 300 mm including 02 nos. metallic holding brackets, railing etc. fixed with pvc rawl plugs and wooden screws, fixed in repairs, complete all as specified and directed. 51 s&f in repair soap dish brass, chromium plated fancy type fixed to plugs with chromium plated brass screws. 52 s & f in repairs chromium plated shower roses125mm sizewith or without swivel joints, any size, including fixing to steel pipe or union125mm size 53 s & fin repair, kitchen sinks double bowl made of stainless steel 1 mm thick with plugs washers and waster including beeding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 990mm x 420 mm each bowl size 410 mm x 330 mm x 160mm complete all as specified and directed by engineer-in-charge. 54 s & f in repair, kitchen plate rack made of stainless steel 1 mm thick with plugs washers asoverall size of 75cm x 75 cm including fixing to wall and all assessaries complete all as specified and directed by engineer-in-charge. 55 s&f in repair pvc cabinet mirror of size 400 mm x 500 mm as approved by garrison engineer. 56 s&f in repair looking mirror 600 mm x 450 mm beveled edge mirror of selected quality glass mounted on 6 mm thick commercial plywood with decorative type wooden frame and fixed to wooden plugs with steel screws, complete all as specified. 57 s&f in repairs towel rail 600 mm long, 20 mm dia, ‘d’ type, brass chromium plated, fixed to walls with screws and plastic cleats, complete all as specified. 58 s&f in repairs brass chromium plated grating doom 125mm diawith or without hole complete all as specified and directed. 59 taking down eaves gutter and rainwater pipes (any size or pattern), including all fittings complete all as specified and as directed. 60 s&f 110 mm bore pvc (swr) pipes with, single socketed in any length with rubber ring joints fixed to walland making good the mouth of rain water pipe as directed complete all as specified. 61 s&f 110 mm bore pvc (swr) bends any radius, fixed with solvent cement in any position as per site requirement complete all as specified. 62 s&f in repairs stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays suitable for 110 mm bore pvc pipe, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed. 63 dismantling of cast iron or reinforced concrete drain pipes, 75/100 mm dia pipe jointed in cement mortar and taking out of trenches, if required complete all as specified and directed. 64 s&f in repair 75 mm cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type b-1 (1:2:4)complete all as specified and directed. 65 s&f 75 mm borecast iron soil spun pipes, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors 66 s&f 75 mm borecast iron soil spun pipes, waste and vent pipes in any length with or without ears, with cement joints,fixed to walls 67 s&f 100 mm borecast iron soil spun pipes, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors 68 s&f 100 mm borecast iron soil spun pipes, waste and vent pipes in any length with or without ears, with cement joints,fixed to walls 69 s&f in repair 75 mm cast iron bends (any radius),diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified 70 s&f in repair 75 mm cast iron bends (any radius) with ducks foot or heel restcomplete all as specified 71 s&f in repair 100 mm cast iron bends (any radius) with ducks foot or heel restcomplete all as specified 72 s&f inrepair100 mm cast iron t, single (equal or unequal),ordinary or inverted (spigot or socket type)or with parallel branches complete all as specified 73 s&f in repair 100 mm cast ironsockets (double) collars complete all as specified 74 demolition of lime concrete/ lean concrete/ brick bats from sunken portion exc. 15 cm thickness (above ground level), including removal of rubbish outside mod land, complete all as specified. 75 water proofing treatment to sunken portion of wcs, bathroom etc. by applying cement slurry mixed with acrylic based polymer modified cementitious composite compound coating of make as approved in technical instruction 5/ 2003:-(a) 15 mm thick plaster (1:4) in cement sand mortar with integral water proofing compound 2 % by weight of cement on floor and wall,finishing the surfaces even and smooth without using extra cement. the surface shall then be cured and allowed to dry.(note: supply only water proofing compound shall be measured and paid separately).(b) first layer of slurry of cement @ 0.488 kg/sq.m mixed with acrylic based polymer modified cementitious composite compound @ 0.253 kg/sq.m.this layer will be allowed to air cure for 4 hrs.(c) second layer of slurry of cement @ 0.242 kg/sq.m mixed with acrylic based polymer modified cementitious composite compound @ 0.126 kg/sq.m.this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. 76 s&f steel water tubes, 40 mm bore, medium grade, galvanized, as in spoutfor sunken floor, fixed in wall, inside end fixed with wire netting and external beveled edge at 45 degree, complete all as specified and directed by engineer - in -charge. 77 m&l lean concrete (1:5:10), type e-2, using40 mm brick coarse aggregate, as in sunken portion, complete all as specified and directed by engineer-in-charge. 78 demolition of cement concrete (reinforced), of any description & in any position (below or above ground level), any thicknessand any length, including removal of rubbish outside mod land, upto 15 mtr complete all as specified and directed. 79 providing cement concrete (1:2:4), type b-1, (using 20 mm graded crushed stone aggregates),slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified. 80 mild steel tmt bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binderscut to length, bent to shape required, including cranking, bending etc., and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified. 81 m&l for providing precast cement concrete asin landings, cover slabs (for man holes etc.)chullah hoods,chajjas, water troughs, mangers, shelves and similar articles with plain face of type b1 1:2:4 using 20mm grade3d aggtregate set in cm 1:4 complete. 82 demolition of brick masonry in any position built in any cement mortar, complete all as specified. 83 taking down cement plaster on brick or concrete surfaces of wall/ceiling and likesincluding racking outjoints, hacking for keys scrubbing down with water etc any description , complete all as specified and directed. note : the rate quoted by the contractor is deemed to be included necessary scafolding and form works. 84 m&l for brick work with sub class ‘b’ bricks, straight or curved on plan exceeding 6 metre mean radius in cement mortar (1:6), using old size bricks, complete all as specified. 85 m&l for brick work with sub class ‘b’ bricks (except bricks) straight or curved on plan exceeding 6 metre mean radius in cement mortar (1:6), using old size bricks, complete all as specified.(old brickobtained from item no 82 herein before shall be reused. the cost of cleaning & washing bricks is deemed to be included in the unit rate quoted. 86 m&l for brick work with sub class ‘b’ bricks, straight or curved on plan exceeding 6 metre mean radius in cement mortar (1:4), using old size bricks, in half brick wall complete all as specified. 87 m&l for rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement, complete all as specified. 88 m&l for rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:6) finished even and fair without using extra cement, complete all as specified. 89 m&l for rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such aschajjas, balcony,mumty and staircase flight ceiling etc.) finished even and smooth without using extra cement, complete all as specified and directed by engineer - in -charge.note for item no. 87 to 89 : the rate quoted by contractor is deemed to be included necessary scaffolding and form work as required upto 12.00 mtr height building. 90 material and labour preparation of new plastered surfaces and apply two coats of water based distmperover 1mm thick wall care putty to smoothening the surface by using sand paper, complete all as specified and directed. 91 m&l for preparation of newly plastered surfaces of wall andmaterial & labour for applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm/litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. 92 complete removal exixting treatmen and material & labour for applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm/litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed. note: weather proof exterior emulsion paint and primer shall be of same manufacturer. 93 m&l for complete removal of existing treatment from internal surfaces of walls by wire brushes and applying 1mm thick cement wall care putty to obtain smooth regular/even finish surfaces by using sand paper and applying two coats of water based distemper over one coat of primer of the same manufacturer complete all as specified and directed. 94 m&l for complete removal of existing treatment from internal surfaces of ceiling s by wire brushes and applying 1mm thick cement wall care putty to obtain smooth regular/even finish surfaces by using sand paper and applying two coats of water based distemper over a coat of primer of the same manufacturer complete all as specified and directed. 95 m&l for prepartation of old painted wooden surfaces over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed. 96 m&l for prepartation of old painted steel or iron surfaces over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed.note for srl item no. 90 to 95 :- the rates quoted against these items deemed to include the use of scafolding, ladders, cradles etc, removing nails, making good holes, cracks etc, removing and placing furnitures, cleaning cup boards, washing floors, floor and wall tiles,cleaning joinery glasses, joinerys, electric fittings, wiring, conduits etc removingdrops, splashes and leaving premises clean and tidy to entire satisfaction of engineer-in-charge. 97 m&l preparing new wood & wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed. 98 m&l for preparation of new or previously steel surfaces of any description, over 10 cm width or girth, not otherwise described and evenly applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 99 s & f instalation pre fabricated/factory made modular kitchen units below main kitchen platform approximate area 42 sqft (elevated area )and each unit having approx 700mm height (exclusive 105mm height pvc adjustable legs) and 610mm depth as per the following specifications:the frame work or cases of the cabinets including drawer fascia/sides/bottom, shelves etc shall be made out of 19 mm thick marine plywood (of make like green ply/centuryply, kit ply opr equivalentgrade of boiling water prrof and moisture restant) with laminated (plain white) of inside of 0.6mm and 1mm laminated glossy finish over external faces. panel shutter shall be made out of 19mm thick hdf with using 1.0mm decorative laminated glossy finish of make like spacewood/inopan/paracasa or eqivalent of grade of boiling water proof and moisture resistant . each shutter shall be fixed to the frame work using two numbers of soft clsoe auto hinges of make helttich, kaff or approved equivalent make and handle g profile for all drawers doors of reputed approved make . each drawer the fascia shall be made out of 19mm thick hdf (with 10years warranty) of makelike spacewood / inopan paracasaor eqivalent of grade of boiling water proof and moisture restant ) with laminated on both sides and baskets of steelness stell 304 grade with all accessaories ( sampleof bskets to be approved by ge) . it shall be mounted on approved quality high precision soft close telescopic chanels ( 1 sets per drawer( of make kaff, hittachi, hafle or approved equvalent of 45kg capacity to be disegned as per drawer sizeand to meet the wight rrequirement with minimum length of 20 inch to ensure smooth movements of drawers with/without contenet weights. in each kitchen, there should be following units with fittings/fixturs as directed by enginr -in - charge: 100 (a)600mm plain shelf unit. (b) 1000mm hingedunit below sink. (c) 900mm plain shelf unit. (d) 600mm grocery unit. (e ) 600 mm gas cylinder unit. (f) 600 mm coocking cultery unit (g) 800 mm plain shel unit. (h) 1 nos detergent holders. (j)1 nos dustbin holders.(k)filler 30mm. 101 (b) supplying pre- fabricated factory made overhead kitchen wall units aboe main kitchen platform havingbox type overhead units approx length of 2400mm (in two parts) and 700mm heights and 325mm depth as per following specifcation: the frame work or cases of the cabinets including drawer fascia/sides/bottom, shelves etc shall be made out of 19mm thick marine plywood (of make like green ply/centuryply, kit plyor equivalentgrade of boiling water prrof and moisture restant) with laminatedof inside of 0.6mm and 1.0mm laminated glossy finish panel door(approx 18sqft per kitchen) shall be made out of 19mm thick hdf withglossy finish(with 10years warranty) of make like spacewood / inopan paracasaor eqivalent of grade of boiling water proof and moisture restant. panel door also having provision offixing of 600 thick transparent glass. each shutters shall be fixed to the frame work using two numbers of soft close auto hinges of make helttich, kaff or approved equivalent make and handle g profile(approx 7 feet per kitchen) of reputed approved make. . in each kitchen, there should be following units with fittings/fixturs as directed by enginr -in - charge: (a) 02 nos of 1200mm plain shelf unit(rate inncluded for110 a&b complet specifiaction) 102 taking down chowkhats with shutters without taking of shutter from the frame of any description not exceeding 1.50 sq. m each,complete all as specified 103 taking down chowkhats with shutters without taking of shutter from the frame of any description exceeding 1.50 sq. m but not exceeding 4.00 sq. m each, complete all as specified 104 taking down shutter of any description exc1 sq. m and n exc2sqm complete all as specified. 105 supply and fix, factory made pressed steel frames for doors with one or more rebates, of size 125mmx60mm, made out of 1.25mmthick sheet,including necessary fixing lugs, hinges, lock strike plate,including cement concrete 1:2:4 with 12.50 mm graded stone aggregate in backfilling of chowkhats etc, complete all as specified and directed. 106 supply and fix, factory made pressed steel frames for doors with one or more rebates, of size 105mmx60mm, made out of 1.25mmthick sheet,including necessary fixing lugs, hinges, lock strike plate,including cement concrete 1:2:4 with 12.50 mm graded stone aggregate in backfilling of chowkhats etc, complete all as specified and directed. 107 s & f framed work as in doors/chowkhats or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or othercovering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete of fe 410 -w (gdee- 250) qualitya 108 supply and fix, flush shutters 35mm thick,solid core construction with particle board core and plywood face panels commercial type on both sides, duly provided with 6mm thick teakwood leeping on edges alround, fitted to chowkats, complete all as specified & directed. 109 m&l for 35 mm thick factory made 2ndclass hardwood (hollock) skeleton shutters, open rebated and prepared to receive wire cloth, glass etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, wire cloth etc., sizes of members of shutters as specified in ssr part-i section 8 clause 8.24(a), complete all as specified. 110 s & f factory made single extruded wpc (wood polymer composite) solid door/ window/ s & f ceosetory windows & other frames/chowkhat of size 45 x 70 mm comprising of virgin pvc polymer of k value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying pvc solvent cement and screwed with full body threaded star headed ss screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 n (face) & 1100 n (edge), minimum compressive strength of 58 n/mm2, modules of elasticity 900 n/mm2 and resistance to spread of flame of class a category with property of being termite/ borer proof,water/ moisture proof and fire retardant and fixed in position with ms hold fast/lugs/ss dash fasteners of required dia and length complete as per direction of engineer-in-charge. (m.s. hold fast/ lugs or ss dash fasteners shall be paid for separately). 111 providing and fixing factory made single extruded wpc (wood polymer composite) solid plainflushdoor shutter of size 30mm thick comprising of virgin polymer of k value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 n (face) & 900 n (edge), minimum compressive strength 50 n/mm2, modulus of elasticity 850 n/mm2 and resistance to spread of flame of class a category with property of being termite/borer proof, water/moisturproof and fire retardant. wpc to be laminated with pvc foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk s.s screws, all as per direction of engineer- in- charge. (note: stainless steel butt hinges and necessary s.s screws shall be paid separately) 112 s&ftype b-21, 100 mm, isi marked, butt hinges, heavy duty, medium weight, stainless steel steel hinge pin, anodised and fixed, complete all as specified. 113 supply and fixing, 150mm long, aluminium anodized, barrel tower bolts of extruded section, isi marked, complete all as specified and directed. 114 supply and fix 150mm size aluminum handle, d type,anodized, isi marked, complete all as specified and directed. 115 s&f 300mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy, isi marked, complete. 116 s&f spring for doors 300 mm mild steel ordinary rat tail rod pattern spring including roller & roller plate, complete all as specified. 117 s& f factory made box type glazed and gauged steel window/ventilator made out of erw hollow p&t section. both window to be welded together with flat iron 25x3mm to outer frames on both sides complete all as specified and shown in drawing no ceaf/std-184/2012 sheet no 1/3, 2/3 & 3/3, including ms grill and necessary formwork complete and including shop coat redoxide primer with following fittings welded to frame/shutter:-(a) hold fast 150mm long 25mmx6mm iron made to shape-02 nos in each window (both sides)(b)handle of z section 20mmx25mm each leaf(c)100mm stopper-01 no per leaf.(d) ms tower bolt 150mm long- 02 nos in each leaf.(e) cleat 55mm long of hollow square 15mmx15mmx24mm welded to hinges gauze wall thickness welded to hinges of 50mm size-01 no per leaf.(f) ms box type hinges of size 75x12mm-03 nos per leaf(g) fabrication & fixing complete(h) flat iron for fixing wire gauge to gauged window.(j) glass pane, wire gauge and synthetic enamel painting work complete.note:- (i) glass panes, wire gauze and painting shall be measured & paid separately under respective items.(ii) design shall be got approved from the engineer-in-charge as per drg no ceaf/std-184/2012 sheet no 1/3, 2/3 & 3/3 before fabrication and bulk order to the manufacturer. 118 s&f for factory made box type steel window/ventilatorfixed type, dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed. 119 providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows,ventilators and partitions (fixed portions) with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, c.p.brass/ stainless steel screws, all complete as per architectural drawings and the directionsof engineer-in-charge 120 m&l for powder coated aluminium (minimum thickness of powder coating 50 micron) window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws,powder coated fittings such as peg stays 150mm long (1 no.). hinges type b-21 100mm long (2 no.) suitable handle (1no.) complete all as specified 121 supply and fixing, stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to steel frames with tinned tacks, or galvanized wire staples, or fixed to wooden /steel frames with first class hard wood bead,/ flat iron stripcomplete all as specified and directed. 122 s & f 3mm thick sheet glass ordinary quality and glazing with oil putty or wooden bead in squares not exceeding 0.5 sq. m in each pane, complete all as specified. note:- new wooden required for glazing glass in wooden window will be paid for separately. 123 s & f 3mm thick frosted glass, pin headed type and glazing with oil putty or wooden bead in squares not exceeding 0.5 sq. m in each pane, complete all as specified. 124 mild steel framed work such as grills, gratings, etc. with ends ofbars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; and similar work conforming to fe-290 gde-e-165, complete all as specified. 125 s&f ms chroumium plated curtain rod 25 mm diawith and incl ms chromium plated decorative round funnals on either end and provide a visually balanced appearance incl ms chromium plated brackets fixed to wall with 30mm wooden steel screws and pvc rawal plug anchors and installation as fixed in repairs complete all as specified. 126 taking down shutterexc 1 sq. m and n exc2sq. m each of any description and re - fixing in same opening 127 taking down shutter n. exc 1 sq. m each of any description and re fixing in same opening . 128 demolition of cement concrete in groundfloors & pavings n exc 15cm thickness (below or above ground level) all as specified. 129 m & l 50 mm thick, plain cement concrete 1:3:6, type c-2, using 40 mm graded mechanically crushed stone aggregates, laid in 1:20 slope as in plinth protection/pavings/shafts including making joints at 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/ 25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement, complete all as specified. note: the concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm. 130 material and labour, coloured chequered cement concrete tiles 250mmx250mmx22mm thick, factory made, isi marked (is 13801-1993), with grey cement &pigment, laid with neat cement slurry @ 3kg/sqm over & including 20mm thick screed bed of cement mortar (1:6), pointed in white cement and pigment, complete all as specified and directed. 131 s&fjoist, channel, angle, or tee sections,fe 410 -w (gde e- 250)quality-a connected each other by welding for making chajja framework and fixed to wall at any height(as per site requirment), without connecting plates, etc. (cut to ordinary lengths i.e. within20mm of the length indicated) complete all as specified 132 s&f pre-painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, sunshed etc fixed with self tapping screws as specified. 133 cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed. 134 pcc (1:2:4), type b-1, using 20 mm graded mechanically crushed stone aggregates,as in holdfast/bed block/coping/benching etc complete all as specified. 135 m&l for taking down rolling shutters, carry out minor repairincluding bearing, shaft etc and greaseing n exc 3.5 mtr height and refixing in the same opening, complete all as specified and directed. 136 s&f1.00 mm thick mild steel, plain, black sheet in wall cladding,steel gates and similarwork, cut to size, holes punched; including round headed screws, clout nails or rivetsand fixed to wood or steel framing with plain 40 mm lap joints with riveted or weldedseams, including bending or turning up, mitred angles, etc. as required complete 137 m & l for prelaminated particle board, interior grade, prelaminated bothside with decorative choice lamination, fixed with screws to timber framework as in as in cupboards, shutters, shelves, pelmet etc. including fixing 18 mm wide 6 mm thick beading of ist class hw (teak) all around, fixed in repairs complete all as specified and directed by engineer-in-charge. 138 supply only integral water proofing compound, complete all as specified. 139 electric works 140 taking down carefully with battens/ pvc surface/ concealed conduit unserviceable copper/ aluminium point wiring (light, fan, socket) complete including fittings such as switches, ceiling roses, pendants, socket etc. and removing unserviceable material from site and making good disturbed surfaces of walls, floors etc. complete all as specified and directed. 141 m&l for point wiring complete with 1.5 sqmm single core pvc insulated unsheathed frls cable 1100 volts grade isi marked with multi stranded copper conductor drawn through and conduit accessories isi marked concealed in wall/fixed to roof ceilint etc and including provision of 1.5 sqmm pvc insulated multistranded unsheated copper conductor cable frls isi marked as earth continuity conductor, farciated sunken terminal box made out of 1.22 mm thick sheet steel duly jpainted concealed in walls, with 3 mm thick bakelite sheet isi marked top cover with brass/chromium plated screws and cup washers for housing switches, socket outlets, fan, regulators etc, all as specified and as directednote :- (i) the chases in the wall shall be cut with elect cutter (ii) the disturbed surfaces of wall shall be made good with cement plaster 1: 4 including matching the surfaces with two coats of white wash / colour wash all as per existing finishes and to the entire satisfaction of engr in charge 142 all as per item no. 141 here-in-before butlight point wiring controlled by twoway switchcomplete all as specified. 143 all as per item no. 141 here-in-before butpoint wiring for one 5amps socket outlet point on independent boardcontrolled by one single pole, one way switchcomplete all as specified. 144 all as per item no. 141 here-in-before butpoint wiring for 2/3 pin 5amps socket outlet point on the same boardcontrolled by one single pole, one way switchcomplete all as specified. 145 all as per item no. 141 here-in-before but point wiring using 2.5 sqmm as main wire & 2.5sqmm as continous earth wire, for one 15amps socket outlet point on independent boardcontrolled by one single pole, one way switch complete all as specified. 146 supply and fix switch piano, modular type, single pole, one way, 6 amp 1 module, 230volts complete all as specified. 147 supply and fix switch piano, modular type, single pole, one way, 16 amp 1 module, 230volts complete all as specified. 148 supply and fix socket outlet 2/3 pin combined, 6 amp modular type 2 module, complete all as specified. 149 supply and fix socket outlet 2/3 pin combined, 6/16 amp modular type 2 module, complete all as specified. 150 supply and fix bell push modular type, single pole, one way, 6 amp 1 module, 230volts complete all as specified. 151 supply and fixing switch modular type, one module ,two way 10a 230volts complete all as specified and directed. 152 supply and fix ceiling rose, two to three terminals, pvc/ isolated body, complete all as specified. 153 supply and fix fan step regulator modular type 120 w 2 module including provision of pvc flexible cable of size 1sqmm copper conductor as required, complete all as specified. 154 supply and fix modular white cover plate with frame of 1 module 155 supply and fix modular white cover plate with frame of 3 module 156 supply and fix modular white cover plate with frame of 4 module 157 supply and fix modular white cover plate with frame of 6 module 158 supply and fix moudlar metal flush box 1/2 module 159 supply and fix moudlar metal flush box 3 module 160 supply and fix moudlar metal flush box 4 module 161 supply and fix moudlar metal flush box 6 module 162 supply andfixing inrepair led lights fitting 1x 20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of size 1. sq. mm from ceiling rose to connector block, complete all as specified and directed by engineer-in-charge. 163 supply and fixing in repairled light fitting mirror type with high put diffuser 2 feet ,10 watt 220 vac decrative type with driver holder connecting up with three core flexible copper conductor cable of suitable size,complete all as specified and as directed. 164 s & f in repair led light fitting 1x9w/1x10wbulkhead luminaires including led light driver holder connecting up with three core fleexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 165 supply and fixing in replacementmcbs distribution board sheet metal enclosures, spn 240 volts, 12 ways with 200 amps rated bus bar, double door, with ip 54 protection, complete all as specified and directed. 166 supply and fixing in replacementmcbs distribution board sheet metal enclosures, tpn 415 volts, 04 ways with 200 amps rated bus bar, double door, with ip 54 protection, complete all as specified and directed. 167 supply and fixing in replacement sheet metal enclosure, spn, with a two pin socket and earth plug, with one mcb single pole, 240 volts, 20 amps, ‘b’ curve, 10 ka, complete all as specified and directed 168 supply and fix in repair mcb 63 amp, 415 volt, tp, breaking capacity 10 ka, b curve, complete all as specified. 169 supply and fix in repair mcb 40 amp, 415 volt, spn, breaking capacity 10 ka, b curve, fixed in repairs, complete all as specified. 170 supply and fix in repair mcb 6 to 32 amp, 240 volt, sp, breaking capacity 10 ka, b curve, fixed inrrepairs, complete all as specified. 171 material and labour for painting ceiling fan after taking down with synthetic enamal paint by spraying ,including filing cavities with filler after cleaning all dust etc and refixing the same in position after painting complete all as specified and directed . 172 supply and fix in replacement exhaust fan, steel body ac single phase. 230v of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed. 173 supply and fix in replacement exhaust fan, steel body ac single phase. 230v of size 250mm sweep with, blades, and frame and louvers complete all as specified and directed. 174 material and labour for sub main wiring (in replacement) with two single core 10 sqmm (nominal area) multi stranded copper conductor frlsh pvc insulated and unsheathed colour code cables, drawn in and including pvc conduit of suitable size with and including one run of continuous multi stranded copper conductor 10 sqmm (nominal area) frlsh pvc insulated and unsheathed colour code cable for earth continuity, 1100 volts grade , complete all as specified and directed. note(s): (i) two runs of 10 sqmm main cable + one run of 10 sqmm cable for earth continuity and pvcconduit shall be measured as one unit/one running metre. 175 material and labour for sub main wiring (in replacement) with two single core 6 sqmm (nominal area) multi stranded copper conductor frlsh pvc insulated and unsheathed colour code cables, drawn in and including pvc conduit of suitable size with and including one run of continuous multi stranded copper conductor 6 sqmm (nominal area) frlsh pvc insulated and unsheathed colour code cable for earth continuity, 1100 volts grade , complete all as specified and directed. note(s): (i) two runs of 6 sqmm main cable + one run of 6 sqmm cable for earth continuity and pvcconduit shall be measured as one unit/one running metre. 176 material and labour for sub main wiring (in replacement) with two single core 4 sqmm (nominal area) multi stranded copper conductor frlsh pvc insulated and unsheathed colour code cables, drawn in and including pvc conduit of suitable size with and including one run of continuous multi stranded copper conductor 4 sqmm (nominal area) frlsh pvc insulated and unsheathed colour code cable for earth continuity, 1100 volts grade , complete all as specified and directed. note(s): (i) two runs of 4 sqmm main cable + one run of 4 sqmm cable for earth continuity and pvcconduit shall be measured as one unit/one running metre. 177 supply and fix in repair led 35 w,ip65,aluminium body,3000lm,input voltage 140-270v,cri>80 suitable as building security light complete all as specified and as directed. 178 supply and fixing in repair 20mm rigid non metallic pvc conduit exclusive of boxes(junction/terminal) but inclusive of all tees,bends,elbow,reducers,bell mouth tube ends and fixing accessories such as coupler ,locknut saddles,pipe hook etc, complete allas specified and directed. 179 supply and fixing in replacement decorativepost toplatern led type 20 watt 230 volts ac outdoor type with 360 degree indirect light ip65protection with resistant to impact and corrosion. anti glare and uniform distribution, complete all as specified and directed. 180 earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not lessthan 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washersconnected to main switch board or main control board or test point, protected by galvanized iron pipe light grade 40mm dia bore, and watering pipe 20mm dia bore gi medium grade with funnel & wire meshincluding all necessary excavation & earth work,pcc chamber in pcc (1:2:4) type b-1 & rcc cover, all as shown in electrical plate no 3 of mes schedule part-i (2009), testing on completion, complete all as specified and directed by engineer-in charge. 181 note: the total amount shall subject to adjustment of credit of rs. 70095.00 for old materials as per schedule of credit.
|