Electrical Industry, Switches and Relay, Switch Supply, Thiruvananthapuram-Kerala

Tender For L3 Switch (4Nos.)1 Hardware And Interface Requirements1.AThe Switch Should Be A Stackable Switch With Minimum 24 X 10/100/1000Baset Ports And OneUplink Slot Populated With 4 X 1/10G Sfp+ Uplink Ports1.B Switch Should Be Available In 24 Port And 48 Port Models1.CSwitch Should Have Dedicated Stacking Ports In Addition To The Above Mentioned Ports AndShould Support A Stacking Bandwidth Of Minimum 176Gbps ((48 X 1G + 4 X 10G) X 2Fd) For LineRate Stacking Between 24 Port And 48 Port Switches In The Same Stack1.DSwitch Should Support Scalability To Support Up To 4 Switches In A Single Stack1.E Switch Should Have An Internal Hot Swappable Redundant Power Supply And Field-Replaceable FanTrays2 Performance Requirements2.A Switching Bandwidth Should Be Should Be Minimum 128Gbps ((24 + 40) X 2Fd) For Line RatePerformance Of A Fully Populated 24 Port Switch2.B Switch Should Have Minimum 94Mpps ((24 + 40) X 1.48Mpps) Forwarding Rate For Line RatePerformance At 64Byte Packet Size For A Fully Populated Switch3 Layer 2 Switching3.A Switch Should Support Minimum 32000 Mac Addresses Per System3.B Switch Should Support Jumbo Frames – 9,000 Bytes3.C Switch Should Support Minimum 4000 Vlans And Vlan Ids3.D Switch Should Support Port-Based Vlan And Mac-Based Vlan3.E Switch Should Support 802.1Q Vlan Tagging3.F Switch Should Support Voice Vlan3.G Switch Should Support Voice Vlan Lldp4 Layer 3 Routing & Multicast4.A Switch Should Support Ipv4 Routing - Static, Ripv1/V2, Ospf, Bgp & Is-Is4.B Switch Should Support Ospfv3 Ipv6 Routing4.C Switch Should Support Pim Sparse Mode (Pim-Sm), Pim Dense Mode (Pim-Dm) And SourcespecificMulticast (Ssm).4.D Switch Should Support Internet Group Management Protocol (Igmp) V1, V2, V3 Snooping For Ipv4And Multicast Listener Discovery (Mld) V1 And V2 For Ipv65 Quality Of Service (Qos ) Requirements5.A Switch Should Support Minimum 8 Hardware Queues Per Port5.B Support 802.1P Class Of Service (Cos) And Dscp Classification, With Marking And ReclassificationOn A Per-Packet Basis By Source And Destination Ip Address, Mac Address, Or Layer 4 Tcp/UdpPort Number.6 System Management And Administration6.A Switch Should Support Snmpv2 And Snmpv36.B Switch Should Support Tacacs+ And Radius Authentication6.C Switch Should Support Ipv6 Management Including Http, Https Over Ipv6, Snmp, Syslog,Telnet And Ssh Over Ipv67 Security Features7.A Switch Should Support Port, Vlan And Router Based Access Control Lists (Acls)7.B Should Support Minimum 3000 Ipv4 Security Acl Entries (Ace)7.C Switch Should Support Mac Limiting7.D Switch Should Support Dynamic Arp Inspection (Dai)7.E Switch Should Support Dhcp Snooping7.F Switch Should Support Control Plane Protection8 Manageability And High Availability8.A Switch Should Be Manageable Through Cli, Web Interface, Sshv2 And Http/Https8.B Switch Should Support Dhcp Server Functions8.C Switch Should Support Local And Remote Port Mirroring8.D Switch Should Support Mirroring Based On Port, Vlan And Acl8.E Switch Should Support Stateful Switchover In By Synchronizes The Layer 2/3 Protocol State FromActive To Standby In A Stack8.F Switch Should Support Synchronization For L2 Protocols: Spanning Tree & Link Aggregation(Lacp)8.G Switch Should Support Synchronization For L3 Protocols: Ospf, Is-Is & Bgp8.H Switch Should Support Non-Stop Forwarding To Ensure Continuity While The Standby SwitchTransitions To Active State8.I Switch Should Support Layer 2 Hitless Forwarding In The Event Of Routing Engine Failure In TheStack8.J Configuration Backup Via Ftp/Secure Copy9 Warranty9.A Switch Should Be Provided With Hardware Replacement Warranty And Ongoing Software UpgradesFor All Major And Minor Releases For A Period Of 3 Years9.B Bidder Should Ensure That There Is A Back-To-Back Agreement With Oem To Meet Above HardwareAnd Software Warranty Terms.

Refer document

Refer document

Refer document