Suply Of A. Cimd-Iv, Btps1. Brass Hexagonal Connector For Hag2. Hex Head Bolt With Nut M 12 X 50 Mm3. Id/Pa Emt (Fiber) Gear 100 Teeth, O.D= 700 Mm4. Id/Pa Cylinder Diaphragm (As Per Sample)5. Brass Connector (As Per Sample) (O.D= 130 Mm, I.D= 20 Mm) & (O.D= 160 Mm, I.D=6. S.S. Spring Guide For Ttp (Electro Step Converter)7. S.S. Spring For Air Lock Relay8. Air Filter Cum Regulator, Range: 0-10 Kg/Cm29. Fibrer-Gear With Fixed Soft Teeth 50Mm Outer Dia: 360Mm For Id Fan Positioner10. Gasket For Electrostep Convertor11. Rubber Coupling Star Type, L=43 Mm, Thick:10.5 Mm12. Rubber Coupling O Type, L=43 Mm, Thick:10.5 Mm13. Rubber Bush For Igniter Gun14. Bolt For Traverse Motor L=75Mm, Thick=8Mm, Thread=26Mm15. Bolt For Lny Type For Rotary Motor L=31Mm, Thick=6Mm, Thread=24Mm16. Ceramic Insulator With Temp. Bearing Cap. 180C For Ignitor Spark Plug.17. S.S Spring For Igniter Spark Plug18. Neoprine Rubber O Ring For Power Unit Kit Of Hydramotor Valve.19. O Ring For Hanson Coupling (As Per Sample).20. Hp/Lp Bypass ‘O’ Ring (As Per Sample)21. Seal Ring For Lm 610 Power Cylinder, Od:37Mm, Id: 30Mm, Thickness: 3.5Mm22. Seal Ring For Id/Fd/Pa Vane Cylinders (As Per Sample)23. Piston Seal Bucket, Od: 35Mm, Id: 23Mm, Thickness: 06Mm24. Spark Plug, Dp Type Ingnitor Gun Assembly25. Hanson Coupling For Oil Lines Dp Type Ignitor Gun Assembly26. Hanson Coupling For Air Lines Dp Type Ignitor Gun Assembly27. Pressure Gauge, 0-2Kg/Cm2 Od:32 Mm Brass Fitting Id:03 Mm28. Pressure Gauge, 0-4Kg/Cm2 Od:32 Mm Brass Fitting Id:03 Mm29. Brass Equilizing Valve For Power Cylinder. 1/4 Npt At Both Ends30. Sector Gear With Key Grove And Key For Hydramotor Valve Actuator.31. Teflon Gromet Used In Dp Ignitor System32. Brass Straight Connector Od:12Mm, Id:06Mm, Connection: 1/2NptB. Emd-I, Btps1. Nipple For H2 Gas Filling Regulator Hexagonal 36X34mm Brass Make (Fig-1).2. Air Vent Valve For H2 Gas Cooler, Brass Make, (Fig-2)3. Galvanized H. T. Bolt Φ 19X115mm With 2 No. Nut, Flat Washer & 01 Spring Washer4. Brass Nut Bolt And 2 No. Flat Washer Φ 5X30mm5. Galvanized H. T. Nut Bolt With 2 No. Flat Washer & One No. Spring Washer 12X75mm.6. Galvanized H.T. Nut Bolt With 2 No. Flat Washer & 01 No. Spring Washer 12X150mm.7. Spindle Made Of S.S. For H2 Gas Filling Post Valve. (Fig.3)8. Stop Nut And Washer For Co2 Gas Filling Pipe, Brass Make, (Fig.4)9. Stud For H2 Gas Cooler (Mat: S.S.) ( Fig.5)10. Gas Trap Valve, Brass Make, ( Fig.11)11. Brass Make Extension Nipple For H2 Gas Post Valve. (Fig.8)12. Insulated Rubber Hand Gloves (20Kvgrade)13. H2 Gas Regulator (Isi Mark), As Per SampleInlet Press: 125-150 Kg/Cm2, Outlet Pressure: 3- 4 Kg/Cm214. Indicating Lamp, 250V, 7W, Screw Type15. Flanged End Gas Valves Suitable For Hydrogen Gas (Bellow Sealed). The H2 Pressure Of SystemIs 3-3.5Kg/Cm2. Material Of Valve (Brass/Al. Alloy) (Fig.9)16. Screw End ½” Gas Valve Suitable For H2 Gas (Bellow Sealed). The H2 Pr. Of System Is 3-3.5Kg/Cm2. Dimension: End To End = 80 Mm, Centre To Top Open = 225Mm, Hand WheelDia = 88Mm, Seat Port Dia = 9.6Mm, Approx. Weight = 3 Kg. Material: Brass (Fig.10)17. Pigmi Lamp, 250V, 15W, Pin Type18. 30A, 2 Pole, 415V, Mcb (Havells Make)19. 6A, 4 Pole, 415V Ac, Mcb (Havells Make) With Mounting Accessories20. Pvc Flexible Sheet (1 X 2 Mtrs) Of Following Thickness:-A. 01 MmB. 03 MmC. 05 Mm21. Neoprene Rubber Sheet Having Shore Hardness 50, Min. Tensile Strength -750 Psi, UltimateElongation- 350% Oil Proof, Suitable For Temp. Up To 200ºf. Sheet Size:1Mx2mA. 03 MmB. 05 MmC. 06 MmD. 08 MmE. 10 Mm
